Menu Structure - Siemens SIRIUS 3RW44 Manual

General Technical Data
9.1

Menu Structure

Display measured value
ESC OK
Device status
Phase voltages
Active parameter set
UL1N
UL2N
UL3N
Phase-to-phase voltages
Type of connection
UL1-L2
UL2-L3
UL3-L1
Blocking voltages
ULT1 Direction of rotation
ULT2
ULT3
Phase currents
Inputs
IL1
IL2
IL3
Power
Line frequency
Supply voltage
Heatsink temperature
Motor heat build-up
Remaining time for tripping
Switch off standard display
Outputs
Order number
Firmware information
** Possible only in connection with creep speed
9-2
Status display
ESC OK ESC
Parameter set 1
Motor 1
Parameter set 1 Rated operating current Ie
Parameter set 2
Rated operating torque
Parameter set 3 Rated operating speed
Copy motor data to PS2 + 3
Starting settings
Unknown/faulty
Star/delta
Starting mode
Inside delta
Unknown
Clockwise
Counter-clockwise
Start voltage
Status - Inputs
Start torque
Input 1 - Action
Limiting torque
No action
Starting time
Manual operation local
Maximum starting time
Emergency start
Current limiting value
Slow speed
Breakaway voltage
Quick stop
Breakaway time
Trip reset
Motor thermal capacity
Motor right PS1
Stopping settings
Motor left PS1 **
Stopping mode
Motor right PS2
Motor left PS2 **
Motor right PS3
Motor left PS3 **
Input 2 - Action [...]
Input 3- Action [...]
Input 4- Action [...] Stopping time
Stopping torque
Dynamic braking torque
Status - Outputs
DC braking torque
Output 1 - Action
Slow speed parameters
No action
Slow speed factor right
PIO output 1
Slow speed torque right
PIO output 2
Slow speed factor left
Input 1
Slow speed torque left
Input 2
Input 3 Current limit values
Input 4
Minimum current limit
Run up
Maximum current limit
Bypass operation
Parameter set 2 [...]
Coasting down
Parameter set 3 [...]
On time motor
Inputs
Command motor-on
Input 1 - Action
DC braking contactor
No action
Group warning
Manual operation local
Group error
Emergency start
Bus error
Slow speed
Device error
Quick stop
Power on
Trip/Reset
Ready to start
Motor right PS1
Output 2 - Action [...]
Motor left PS1 **
Output 3 - Action [...]
Motor right PS2
Output 4 - Action [...]
Motor left PS2 **
Motor right PS3
Motor left PS3 **
Version
Input 2 - Action [...]
Date
Input 3 - Action [...]
Input 4 - Action [...]
Settings
OK
Outputs
Output 1 - Action
Voltage ramp
Voltage ramp + current limiting
Torque control
Torque control + current limiting
Direct on line
Motor heating
Output 2 - Action [...]
Output 3 - Action [...]
Motor protection
Tripping class
Coasting down
Torque control
Pump stop
DC braking
Combined braking
Current asymmetry limit value
Prewarning limit tripping reserve
Prewarning limit motor heat build-up
Idle time
Pre-charge time
Protection against voltage failure
Temperature sensor
Display settings
Language
No action
PIO output 1
PIO output 2
Input 1
Input 2
Input 3
Input 4
Contrast
Run up
Lighting
Operation / bypass
Coasting down
On time motor
Command motor-on
DC braking contactor
Group warning
Group error
Bus error
Device error
Power on
Ready to start
Reaction time keys
None
Auto repeat
CLASS 5 (10a)
CLASS 10
CLASS 15
Activity monitoring time
CLASS 20
Response to ...
CLASS 30
Overload - therm. motor model
Overload - temperature sensor
No
Yes
Current limit value violation
Deactivated
Thermo click
PTC-type A
Overload - contact block
Asymmetry
Ground fault
Name
Name
Saving options
Save settings
Restore settings
Restore basic factory settings
SIRIUS 3RW44 manual
GWA 4NEB 535 2195-02 DS 02
English
Deutsch
Français
Español
Italiano
Português
Brightness
Lighting on
Off with time delay
Lighting off
Response to fault
Unchanged
On
Blinking
Flickering
Response to warning
Unchanged
On
Blinking
Flickering
Time
Speed
Tripping without restart
Tripping with restart
Warning
Tripping without restart
Tripping with restart
Warning
Warning
Tripping
Tripping without restart
Tripping with restart
Warning
Tripping
Warning
Tripping