7: Routing (Routing); Prog 7.3: Ed-Masterfx; 1: Setup - Korg Karma Parameter Manual

7.2–2(...6)a: UTILITY
I
"Write Program" (1.1–1c)
7.2–7: Routing
7.2–7a: Routing
This shows the status of the insert effect settings. ( 7.1–2a)
7.2–7a
7.2–1b: UTILITY
I
"Write Program" (1.1–1c), "Copy Insert Effect," "Swap
Insert Effect" (7.1–1c)
PROG 7.3: Ed–MasterFX
For details on insertion effects, refer to p.159 "7. Effect
Guide."
7.3–1: Setup
Here you can select the master effect types, switch them on/
off, specify chaining, and set the master EQ.
7.3–1a
7.3–1b
7.3–1a: Master Effect Setup
The master effects do not output the direct sound (Dry). The
return level ("Rtn 1, 2") sends the effect sound (Wet) to the L
and R bus, and this is mixed with the direct sound ("BUS
Select" L/R: 7.1–1a, 7.2–1a).
The master effects are monaural input. The sound that is
panned to L and R after passing through the oscillator and
insert effects is mixed to a monaural signal as adjusted by
the "S1 (Send1 (MFX1))" and "S2 (Send2 (MFX2))" levels,
and input to the master effects.
The master effects are mono-in stereo-out. Even when
a stereo-input type effect is selected, the input will be
monaural.
MFX1 On/Off, MFX2 On/Off
Switches master effect 1, 2 on/off. When off, the output will
be muted.
40
(Routing)
7.3–1c
[Off, ON]
Separately from this setting, you can use CC#94 to
switch master effect 1 on/off, CC#95 to switch master
effect 2 on/off. A value of 0 will be off, and a value of 1–
127 will be the original setting. This is controlled on the
global MIDI channel "MIDI Channel" (GLOBAL 2.1–
1a).
Master Effect 1, 2
Indicates the effect type for master effect 1, 2. You can select
from 90 types of effect: 000: No Effect–089: Reverb-Gate.
(Double-size effects cannot be selected.) If 000: No Effect is
selected, the output from the master effect will be muted.
Rtn 1, 2 (Return 1, 2)
Adjusts the return levels from the master effects to the L/R
bus (main output L/MONO, R).
7.3–1b: Chain
7.2–7b
MFX Chain
On (checked): Chain (series connection) will be turned on
for MFX1 and MFX2. ( p.165)
Direction (Chain Direction)
Specifies the direction of the connection when MFX1 and
MFX2 are chained.
MFX1→MFX2: Connect from MFX1 to MFX2.
MFX2→MFX1: Connect from MFX2 to MFX1.
Signal (Chain Signal)
When chain is On, this parameter specifies how the stereo
output signal of the first master effect will be connected to
the input (mono) of the next master effect.
L/R Mix: The stereo output L/R of the first master effect will
be mixed before being input to the next master effect.
L Only, R Only: Only the left or right channel of the output
will be input to the next master effect.
Level (Chain Level)
Sets the send level from the first master effect to the next
master effect when chain is turned on.
7.3–1c: Master EQ Gain [dB]
7.3–1d
Sets the gain for the three-band EQ located immediately
before the sound of the L/R bus is sent from the AUDIO
OUTPUT (MAIN OUT) L/MONO and R jacks. This is
linked with the various "Gain" parameters of Master EQ
(7.3–4).
Low
Mid
High
The cutoff frequency for "Low," "Mid" and "High" and the
"Q" of "Mid" can be adjusted in the MEQ page. These set-
tings are in "dB" units.
[000...089: name]
[000...127]
[Off, On]
[MFX1→MFX2, MFX2→MFX1]
[LR Mix, L Only, R Only]
[000...127]
[–18.0...+18.0]
[–18.0...+18.0]
[–18.0...+18.0]