093: Vocoder - Korg Karma Parameter Manual

Wah
Switches Wah on/off
(Source)
Selects the modulation source that switches the Wah on and off
a
(Sw)
Selects the switching mode for the modulation source that switches
the Wah on and off
SweepRng (Wah Sweep Range)
Sets the range of Wah
b
Src (Source)
Selects the modulation source that controls the Wah
Mode (Drive Mode)
Switching between overdrive and hyper-gain mode
c
Drive
Sets the degree of distortion
Pre Low-cut
d
Sets the low range cut amount of the distortion input
Level (Output Level)
Sets the output level
(Source)
e
Selects the modulation source for the output level
(Amount)
Sets the modulation amount of the output level
Lo (Low Cutoff)
Sets the center frequency for Low EQ (shelving type)
f
G (Gain)
Sets the gain of Low EQ
M1 (Mid1 Cutoff)
Sets the center frequency for Mid/High EQ 1 (peaking type)
Q
g
Sets the band width of Mid/High EQ 1
G (Gain)
Sets the gain of Mid/High EQ 1
M2 (Mid2 Cutoff)
Sets the center frequency for Mid/High EQ 2 (peaking type)
Q
h
Sets the band width of Mid/High EQ 2
G (Gain)
Sets the gain of Mid/High EQ 2
Direct Mix
Amount of the dry sound mixed to the distortion
i
SpSim (Speaker Simulation)
Speaker simulation on/off
W/D (Wet/Dly)
Sets the balance between the effect and dry sounds
(Source)
j
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance

093: Vocoder

This effect applies the character of the right channel signal
(Modulator) to the left channel signal input (Carrier). Sounds
such as rhythm and sound effects are suitable for use as the
modulator, and sounds with rich harmonic structure such as
strings and distortion guitar are suitable for use as the carrier.
Wet: Stereo In - Mono Out / Dry: Stereo In - Stereo Out
Carrier
Left
Lch (Carrier)
+
Trim
Rch (Modulator)
Trim
Band Pass Filter
Right
Modulator
Noise
Generator
Noise Level
214
Fx:006,
Off...Tempo
Tggl, Mmnt
–10...+10
Fx:006,
Off...Tempo
Overdrive, HyperGain
Fx:006,
Off...Tempo
20...1.00kHz
–18...+18dB
300...10.00kHz
–18...+18dB
500...20.00kHz
–18...+18dB
Dry, 1:99...99:1, Wet
Off...Tempo
–100...+100
+
Vocoder /
Carrier
Envelope
Modulator High Mix
Off, On L (Carrier) Trim
a
Sets the input level of left channel (Carrier)
R (Modulator) Trim
b
Sets the input level of right channel (Modulator)
Fx:006
Formant Shift
c
Sets the height of the frequency for the vocoder effect
Response
Fx:006
d
Sets the speed of the response to the modulator input
LoGain (Low Gain)
Sets the low-range output level of the vocoder
e
HiGain (High Gain)
Sets the high-range output level of the vocoder
Noise (Noise Level)
Sets the noise mix level to the Carrier
1...120
(Source)
Fx:006
f
Selects the modulation source for the noise mix level
0...10
(Amount)
Fx:006
Sets the modulation amount for the noise mix level
0...50
Modulator High Mix
g
Sets the high-range output level of the modulator
V/C (Vocoder/Carrier)
Sets the balance between the vocoder output and the Carrier
–50...+50
(Source)
h Selects the modulation source for the balance between the vocoder
output and the carrier
(Amount)
Sets the modulation amount of the balance between the vocoder out-
put and the carrier
W/D (Wet/Dly)
Sets the balance between the effect and dry sounds
0.5...10.0
Fx:006 (Source)
i
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
c: Formant Shift
0.5...10.0
By offsetting the Carrier filter, you can adjust the height of the fre-
Fx:006
quency range to which the vocoder effect is applied. The tonal
quality will change significantly.
f: Noise
0...50
This parameter enables you to mix white noise with the Carrier.
Off, On
g: Modulator High Mix
This parameter sets the high-range output level of the right chan-
nel sound (Modulator). If the modulator is a human voice, it will
make the words more clear.
h: V/C, i: W/D
The "V/C" parameter sets the balance between the vocoder
sound and the left channel sound (Carrier). The "W/D" parame-
ter sets the balance between the effect and dry sound.
If you wish to change the intensity of the vocoder effect, select
Wet for "W/D", and adjust the balance using the "V/C" parame-
ter.
Wet / Dry
Wet / Dry
0...100
0...100
–2...+2
0...100
–12...+12
–12...+12
0...100
,
Off...Tempo
–100...+100
0...100
Carrier, 1:99...99:1, Vocoder
,
Off...Tempo
–100...+100
Dry, 1:99...99:1, Wet
,
Off...Tempo
–100...+100