Recording Time On Cf Card - JVC KA-DV350U Instructions Manual

Using the CF
(Compact Flash)
Recording playback signals of a DV cassette tape on a CF card
Memo Memo
REC START/STOP button
"NO CF FORMAT!" will appear if
t h e i n s e r t e d C F c a r d i s n o t
POWER switch
formatted. Format the card in the
MODE switch
MOVIE CLIP SET menu screen.
☞
MENU button
( page 46)
BAR
( / ) button
<GY-DV300 rear panel>
1.
LCD screen
Turn on the GY-DV300 power.
Check to see that the
viewfinder screen. (When the power is turned on,
C F
will flash during initialization.)
2.
Insert the recorded DV cassette tape.
3.
Set the MODE switch to "VTR".
4.
Set the NETWORK PACK CONFIG menu screen.
C F : Red display during
• Set MPEG REC to "SPLIT".
recording
• Set the video/audio compression in the ENCODE SET menu
: Initializing
• When completed with settings, press the MENU button to
NETWORK PACK CONFIG
menu screen
5.
Press the BAR ( / ) button of GY-DV300 to start DV cassette
N E TW OR K A CK ON I G
P C F
NE T WOR K MA I N S E T U P . .
tape playback.
EN CODE S E T U P . .
MPE G R EC S P I T L
MOV I E CL I P
S E T U P . .
6.
MENU R E S E T CA N CE L
Press the REC START/STOP button or SELECT dial at the
PAGE B ACK
( WMP u n d r 8 ) ( C F V i e w e r ) e
scene to start recording on the CF card.
• During recording, the
• To stop recording, press the SELECT dial.
• To resume recording, press the SELECT dial once more.
Set to SPLIT
ENCODE SETUP
menu screen 7.
To end recording, press the SELECT dial.
* Before turning off the power, check to make sure the
LCD Screen
C F
Memo Memo
• When recording only to the CF card, the clip list will not be registered.
• The CF card remaining warning is displayed on the LCD screen/
viewfinder screen.
• Do not switch over the CAM/VTR mode during recording into the CF card.
CF card remaining
If the mode is switched over during recording, the display of the LCD
warning
viewer can go wrong once in a while. Also, if the mode is switched over
immediately after the start of recording into the CF card, some black
images can be mixed into a recorded picture.
• While recording DV input to a CF Card in the SPLIT mode, do not operate
the VTR section. Recording to the CF Card may stop as a result.
Card
Handle
POWER
OFF ON
MODE
CAM-B
CAM-A VTR
GAIN
SHUTTER
BAR
MENU
SELECT
AW
dial
FWD
REV REC START/STOP button
C F display appears on the LCD screen/
display
screen. ( ☞ page 18)
return to the normal screen.
C F display appears in red.
C F indi-
cator on the LCD screen is white.
Using the CF
Recording
Estimated recording time of CF cards is shown below. The recording time may be shorter than the above estimate
depending on the movement of the subject.
50
Card
(Compact Flash)
BIT RATE
CF memory
card size
384kbps 256kbps
16MByte 3min. 5min.
32MByte 7min. 11min.
64MByte 15min. 22min.
128MByte 30min. 44min.
192MByte 46min. 66min.
256MByte 61min. 88min.
Memo Memo
• Clip file numbers of clip files are generated from the last number of the file in the PC card. If the
last file is erased when the power is turned on, that number will not be used. After formatting,
numbers will be generated from 0001.
• The generated time of the clip file is the time when recording is completed.
Recording time on
a CF card
128kbps ~ 56kbps
10min. or more
20min. or more
40min. or more
80min. or more
120min. or more
160min. or more
51