Summary of Contents for neighbor Haven 8-Piece U Sectional Teak Arm
Page 1
Haven 8-Piece U Sectional Teak Arm Assembly Guide...
Page 2
Components Assembly Instructions Contact Frame Boxes Left Module - Teak Arm Frame (1) Right Module - Teak Arm Frame (1) Armless Module Frame (4) Corner Module Frame (2) Cushion Boxes Cushions - Armless/Teak Arm (6) Cushions - Corner Module (2)
Page 3
Components Assembly Instructions Contact Parts Module Back Support Left Module - Teak Arm Frame Box Right Module - Teak Arm Frame Box Armless Module Frame Box Module Roped Back Left Module - Teak Arm Frame Box Right Module - Teak Arm Frame Box Armless Module Frame Box Module Bases Corner Module Base...
Page 4
Components Assembly Instructions Contact Cushions Hardware 30mm Hex Bolt All Frame Boxes Module Back Cushion Armless/Teak Arm Cushion Box 40mm Hex Bolt Left Module - Teak Arm Frame Box Right Module - Teak Arm Frame Box Module Base Cushion Armless/Teak Arm Cushion Box 60mm Hex Bolt Corner Module Frame Box Long Corner Module Back Cushion...
Components Assembly Instructions Contact Assembly Tips Use caution when lifting Assemble on a soft surface Two-person lift is recommended. The boxes We recommend assembling your furniture on a and product are both large and heavy. soft surface such as a rug or a towel. The wood frame can scratch against harsh textures like Lay everything out before you begin brick or concrete.
Page 7
Corner/Armless Components Assembly Instructions Contact Long Corner Leg only has two drill holes Connect legs to corner base Gently connect the Long Corner Leg, two Long Legs, and the Short Corner Leg to the Corner Module Base.
Page 8
Corner/Armless Components Assembly Instructions Contact 30mm Hex Bolt 60mm Hex Bolt Fasten legs to corner base Using the Allen Wrench provided, fasten the Corner Leg with two 60mm Hex Bolts. Then, secure both Long Legs with two 30mm Hex Bolts per leg and the Short Corner Leg with four 30mm Hex bolts, leaving two threaded holes on each leg exposed as demonstrated.
Page 9
Corner/Armless Components Assembly Instructions Contact Backrest slots should align with the Long Leg, as shown Connect legs to right side of base Gently connect the Long and Short Legs to the right side of the Module Base, verifying that the backrest slots are aligned with the Long Leg.
Page 10
Corner/Armless Components Assembly Instructions Contact 30mm Hex Bolt 30mm Hex Bolt Fasten legs to base With the Allen Wrench provided, fasten the Short Leg to the Module Base with two 30mm Hex Bolts. Repeat with Long Leg. Be sure to leave two threaded holes on each leg exposed as demonstrated.
Page 11
Corner/Armless Components Assembly Instructions Contact Connect bases Gently slide Module Base into the slotted sections on the assembled corner component’s Long and Short Legs. Slide base until its pre-drilled holes align with the threaded holes on the legs.
Page 12
Corner/Armless Components Assembly Instructions Contact 30mm Hex Bolt Fasten bases After holes on the bases are aligned with the corresponding threaded holes on each leg, use the Allen Wrench provided to fasten them 30mm Hex Bolt together with two 30mm Hex Bolts per side.
Page 13
Corner/Armless Components Assembly Instructions Contact Drain holes face down Secure roped backs to bases Insert the Module Roped Back into the slots of the Module Base. Then, insert the Corner Module Roped Backs into the slots of the Corner Module Base.
Page 14
Corner/Armless Components Assembly Instructions Contact Attach back supports to roped backs Lower the Module Back Support onto the Module Roped back and the Corner Module Back Support onto the Corner Module Roped Backs. Fit the tabs into their corresponding slots, then insert.
Page 15
Corner/Armless Components Assembly Instructions Contact 60mm Hex Bolt Fasten back supports 30mm Hex Bolt Fasten the Corner Module Back Support to the Long Corner Leg with two 60mm Hex Bolts. 30mm Hex Bolt Then, fasten the back supports to the three remaining Long Legs with eight 30mm Hex Bolts.
Page 17
Armless/Corner Components Assembly Instructions Contact Long Corner Leg only has two drill holes Connect legs to corner base Gently connect the Long Corner Leg, two Long Legs, and the Short Corner Leg to the Corner Module Base.
Page 18
Armless/Corner Components Assembly Instructions Contact 60mm Hex Bolt 30mm Hex Bolt Fasten legs to corner base Using the Allen Wrench provided, fasten the Corner Leg with two 60mm Hex Bolts. Then, secure both Long Legs with two 30mm Hex Bolts per leg and the Short Corner Leg with four 30mm Hex bolts, leaving two threaded holes on each leg exposed as demonstrated.
Page 19
Armless/Corner Components Assembly Instructions Contact Backrest slots should align with the Long Leg, as shown Connect legs to left side of base Gently connect the Long and Short Legs to the left side of the Module Base, verifying that the backrest slots are aligned with the Long Leg.
Page 20
Armless/Corner Components Assembly Instructions Contact 30mm Hex Bolt 30mm Hex Bolt Fasten legs to base With the Allen Wrench provided, fasten the Short Leg to the Module Base with two 30mm Hex Bolts. Repeat with Long Leg. Be sure to leave two threaded holes on each leg exposed as demonstrated.
Page 21
Armless/Corner Components Assembly Instructions Contact Connect bases Gently slide Module Base into the slotted sections on the assembled corner component’s Long and Short Legs. Slide base until its pre-drilled holes align with the threaded holes on the legs.
Page 22
Armless/Corner Components Assembly Instructions Contact 30mm Hex Bolt Fasten bases After holes on the bases are aligned with the corresponding threaded holes on each leg, use the Allen Wrench provided to fasten them 30mm Hex Bolt together with two 30mm Hex Bolts per side.
Page 23
Armless/Corner Components Assembly Instructions Contact Drain holes face down Secure roped backs to bases Insert the Module Roped Back into the slots of the Module Base. Then, insert the Corner Module Roped Backs into the slots of the Corner Module Base.
Page 24
Armless/Corner Components Assembly Instructions Contact Attach back supports to roped backs Lower the Module Back Support onto the Module Roped back and the Corner Module Back Support onto the Corner Module Roped Backs. Fit the tabs into their corresponding slots, then insert.
Page 25
Armless/Corner Components Assembly Instructions Contact 30mm Hex Bolt Fasten back supports Fasten the Corner Module Back Support to the Long Corner Leg with two 60mm Hex Bolts. 60mm Hex Bolt Then, fasten the back supports to the three remaining Long Legs with eight 30mm Hex Bolts. 30mm Hex Bolt...
Page 26
Left Arm/Armless Components Assembly Instructions Contact Left Arm/ Armless...
Page 27
Left Arm/Armless Components Assembly Instructions Contact Backrest slots should align with the back of the armrest, as shown Connect base to left arm Place the Left Teak Arm on a soft surface with the armrest facing down. Gently insert the Module Base into the arm’s inner slots.
Page 28
Left Arm/Armless Components Assembly Instructions Contact 30mm Hex Bolt Fasten arm to base Using the Allen Wrench provided, fasten the Module Base to the Left Teak Arm with two 30mm Hex Bolts per side.
Page 29
Left Arm/Armless Components Assembly Instructions Contact 30mm Hex Bolt Fasten short leg to base Using the Allen Wrench provided, fasten the Short Leg to the front right side of the Module Base with two 30mm Hex Bolts. Be sure to leave two threaded holes exposed as demonstrated.
Page 30
Left Arm/Armless Components Assembly Instructions Contact 30mm Hex Bolt Fasten long leg to base Stand the assembled components upright. With the Allen Wrench provided, fasten the Long Leg to the Module Base with two 30mm Hex Bolts. Be sure to leave two threaded holes exposed as demonstrated.
Page 31
Left Arm/Armless Components Assembly Instructions Contact Connect bases Gently slide Module Base into the slotted sections on the assembled arm component’s Long and Short Legs. Slide base until its pre-drilled holes align with the threaded holes on the legs.
Page 32
Left Arm/Armless Components Assembly Instructions Contact 30mm Hex Bolt Fasten bases After holes on the bases are aligned with the corresponding threaded holes on each leg, use the Allen Wrench provided to fasten them together with two 30mm Hex Bolts per side. 30mm Hex Bolt...
Page 33
Left Arm/Armless Components Assembly Instructions Contact Drain holes face down Secure roped backs to bases Insert the Module Roped Backs into the slots of the Module Bases.
Page 34
Left Arm/Armless Components Assembly Instructions Contact Attach back supports to roped backs Lower each Module Back Support onto the Module Roped Backs by fitting the tabs into their corresponding slots, then insert.
Page 35
Left Arm/Armless Components Assembly Instructions Contact 40mm Hex Bolt Fasten back supports Fasten the Module Back Supports onto the Long Leg with four 30mm Hex Bolts. Then, fasten the Module Back Support to the Teak Arm with two 30mm Hex Bolt 40mm Hex Bolts.
Page 36
Armless/Right Arm Components Assembly Instructions Contact Armless/ Right Arm...
Page 37
Armless/Right Arm Components Assembly Instructions Contact Backrest slots should align with the back of the armrest, as shown Connect base to right arm Place the Right Teak Arm on a soft surface with the armrest facing down. Gently insert the Module Base into the arm’s inner slots.
Page 38
Armless/Right Arm Components Assembly Instructions Contact 30mm Hex Bolt Fasten arm to base Using the Allen Wrench provided, fasten the Module Base to the Right Teak Arm with two 30mm Hex Bolts per side.
Page 39
Armless/Right Arm Components Assembly Instructions Contact 30mm Hex Bolt Fasten short leg to base Using the Allen Wrench provided, fasten the Short Leg to the front left side of the Module Base with two 30mm Hex Bolts. Be sure to leave two threaded holes exposed as demonstrated.
Page 40
Armless/Right Arm Components Assembly Instructions Contact 30mm Hex Bolt Fasten long leg to base Stand the assembled components upright. With the Allen Wrench provided, fasten the Long Leg to the Module Base with two 30mm Hex Bolts. Be sure to leave two threaded holes exposed as demonstrated.
Page 41
Armless/Right Arm Components Assembly Instructions Contact Connect bases Gently slide Module Base into the slotted sections on the assembled arm component’s Long and Short Legs. Slide base until its pre-drilled holes align with the threaded holes on the legs.
Page 42
Armless/Right Arm Components Assembly Instructions Contact 30mm Hex Bolt Fasten bases After holes on the bases are aligned with the corresponding threaded holes on each leg, use the Allen Wrench provided to fasten them together with two 30mm Hex Bolts per side. 30mm Hex Bolt...
Page 43
Armless/Right Arm Components Assembly Instructions Contact Drain holes face down Secure roped backs to bases Insert the Module Roped Backs into the slots of the Module Bases.
Page 44
Armless/Right Arm Components Assembly Instructions Contact Attach back supports to roped backs Lower each Module Back Support onto the Module Roped Backs by fitting the tabs into their corresponding slots, then insert.
Page 45
Armless/Right Arm Components Assembly Instructions Contact 30mm Hex Bolt Fasten back supports Fasten the Module Back Supports onto the Long Leg with four 30mm Hex Bolts. Then, fasten the Module Back Support to the Teak Arm with two 40mm Hex Bolts. Finally, connect all assembled 40mm Hex Bolt module components with six 30mm Hex Bolts.
Page 46
Armless/Right Arm Components Assembly Instructions Contact Add cushions With the zipper seam facing backward, add base cushions. Finally, add the back cushions. Relax! You’re ready to enjoy your sectional.
Page 47
Components Assembly Instructions Contact Contact Have a question, comment, feedback? We love hearing from customers. support@hineighbor.com hineighbor.com...