Summary of Contents for neighbor The 8-Piece U-Shaped Sectional
Page 1
The 8-Piece U-Shaped Sectional Assembly Guide B O X E S N E E D E D : Left Arm Module Frame Left Arm Module Cushions Right Arm Module Frame Right Arm Module Cushions Armless Module Frame Armless Module Cushions Corner Module Frame Corner Module Cushions...
Page 2
Components Assembly Instructions Contact Parts Long Base Short Base Right Arm Corner Base Left Arm Left Arm Module Frame Box Armless Module Frame Box Right Arm Module Frame Box Corner Module Frame Box Left Arm Module Frame Box Right Arm Module Frame Box Small Roped Back Corner Block Leg Large Roped Back...
Page 3
Components Assembly Instructions Contact Cushions Base Cushion Back Cushion Arm Cushion Left Arm Module Cushion Box (1) Left Arm Module Cushion Box (1) Left Arm Module Cushion Box Right Arm Module Cushion Box (1) Right Arm Module Cushion Box (1) Right Arm Module Cushion Box Armless Module Cushion Box (4) Armless Module Cushion Box (4)
Page 4
Components Assembly Instructions Contact Hardware Hex Bolt Long Hex Bolt Screw L-Bracket All Frame Boxes Corner Module Frame Box Left Arm Module Frame Box Left Arm Module Frame Box Right Arm Module Frame Box Right Arm Module Frame Box Tools Allen Wrench Phillips Head Screwdriver All Frame Boxes...
Page 5
Components Assembly Instructions Contact Assembly Tips Product Care • Spray on a mild cleaning solution of soap Exercise caution while lifting Caring for teak Two-person lift is recommended. Both the Unfinished teak will gradually change color (such as Woolite® or Dawn®) and water. boxes and the product itself are large and heavy from a honey gold to a silver-grey patina.
Page 6
Components Assembly Instructions Contact Step 3 Step 2 Step 1 Left Arm/Armless Corner/Armless Armless/Corner (p. 34) (p. 7) (p. 16) Building your U-shaped sectional Your 8-Piece U-Shaped Sectional can be assembled in sections. Start by first assembling the Corner/Armless section, then work outward to the additional Armless and Arm components.
Page 8
Corner/Armless Components Assembly Instructions Contact Long Hex Bolt Fasten legs to corner base Using the Allen wrench, fasten two large legs and the assembled corner block leg onto the corner base with hex bolts. Use two long hex bolts when fastening corner Corner Block base to corner leg.
Page 9
Corner/Armless Components Assembly Instructions Contact Fasten legs to right side of short base With the Allen wrench, thread two hex bolts through the holes in the front right side of the short base. Fasten to the short leg. Repeat this with the large leg on the back right corner of the small base.
Page 10
Corner/Armless Components Assembly Instructions Contact Connect small base with corner base Gently slide small base into the grooves located on the large leg and corner block of the corner base. Align the holes located on the small base with the corresponding threaded holes on the corner base.
Page 11
Corner/Armless Components Assembly Instructions Contact Fasten small base to corner base Secure the two bases by inserting four bolts through the holes on the small base. With the Allen wrench, gently fasten them to the four threaded holes located on the corner base.
Page 12
Corner/Armless Components Assembly Instructions Contact Drain hole faced down Secure roped backs to bases Insert the lower brackets of the small roped back components into the slots of the short and corner base.
Page 13
Corner/Armless Components Assembly Instructions Contact Attach back supports to roped backs Insert armless module back support and corner module back support onto the top brackets located on roped backs by inserting them into corresponding slots underneath the back supports.
Page 14
Corner/Armless Components Assembly Instructions Contact Long Hex Bolt Fasten backs to large legs With your Allen wrench, gently fasten armless back support and corner module back support onto the threaded holes on the top of the large legs with hex bolts. Use two long hex bolts in the back in the far corner of the corner module back support.
Page 15
Corner/Armless Components Assembly Instructions Contact Add base and back cushions After successfully assembling the Armless to Corner Module and fastening them to other modules, you can finally add your cushions (zipper facing backward). Time to relax!
Page 17
Armless/Corner Components Assembly Instructions Contact Long Hex Bolt Fasten legs to corner base Using the Allen wrench, fasten two large legs and the assembled corner block leg onto the corner base with hex bolts. Use two long hex bolts when fastening corner Corner Block base to corner leg.
Page 18
Armless/Corner Components Assembly Instructions Contact Fasten legs to left side of short base With the Allen wrench, thread two hex bolts through the holes in the front left side of the short base. Fasten to the short leg. Repeat this with the large leg on the back left corner of the small base.
Page 19
Armless/Corner Components Assembly Instructions Contact Connect small base with corner base Gently slide small base into the grooves located on the large leg and corner block of the corner base. Align the holes located on the small base with the corresponding threaded holes on the corner base.
Page 20
Armless/Corner Components Assembly Instructions Contact Fasten small base to corner base Secure the two bases by inserting four bolts through the holes on the small base. With the Allen wrench, gently fasten them to the four threaded holes located on the corner base.
Page 21
Armless/Corner Components Assembly Instructions Contact Drain hole faced down Secure roped backs to bases Insert the lower brackets of the small roped back components into the slots of the short and corner base.
Page 22
Armless/Corner Components Assembly Instructions Contact Attach back supports to roped backs Insert armless module back support and corner module back support onto the top brackets located on roped backs by inserting them into corresponding slots underneath the back supports.
Page 23
Armless/Corner Components Assembly Instructions Contact Long Hex Bolt Fasten backs to large legs With your Allen wrench, gently fasten armless back support and corner module back support onto the threaded holes on the top of the large legs with hex bolts. Use two long hex bolts in the back in the far corner of the corner module back support.
Page 24
Armless/Corner Components Assembly Instructions Contact Add base and back cushions After successfully assembling the Armless to Corner Module and fastening them to other modules, you can finally add your cushions (zipper facing backward). Time to relax!
Page 25
Components Assembly Instructions Contact Armless/ Right Arm...
Page 26
Armless/Right Arm Components Assembly Instructions Contact Connect large base to right arm Place the right arm component on a soft surface, verifying that the two screw holes are facing upward. Gently insert the long base into the arm’s inner slots.
Page 27
Armless/Right Arm Components Assembly Instructions Contact Fasten large base to right arm Using the Allen wrench, fasten the large base to both legs of the right arm component with four hex bolts.
Page 28
Armless/Right Arm Components Assembly Instructions Contact Fasten small leg to large base Using the Allen wrench, fasten the small leg to the large base with two hex bolts. Be sure to leave two threaded holes on the small leg exposed as demonstrated.
Page 29
Armless/Right Arm Components Assembly Instructions Contact Connect large and small bases Gently slide small base into the slotted sections on the Right Arm Module’s large and small legs. Slide base until its pre-drilled holes align with the threaded holes on the legs.
Page 30
Armless/Right Arm Components Assembly Instructions Contact Fasten large and small bases After holes on the bases are aligned with the corresponding threaded holes on each leg, use the Allen wrench to fasten them together with two hex bolts per side.
Page 31
Armless/Right Arm Components Assembly Instructions Contact Drain hole faced down Secure roped backs to large and small bases Insert the lower brackets of the corresponding roped back components into the slots of each base. The Right Arm Module (large base) will require the large roped back and the Armless Module (small base) will require the small roped back.
Page 32
Armless/Right Arm Components Assembly Instructions Contact Attach back supports to roped backs Lower each back support onto the roped backs. The Right Arm Module (large base) will require the right arm back support and the Armless Module (small base) will require the small back support.
Page 33
Armless/Right Arm Components Assembly Instructions Contact Fasten left arm back support to arm and large leg With your Allen wrench, gently fasten right arm back support onto large leg with two hex bolts. Repeat with adjoining side of small back support. Next, align the pre-drilled holes on the right arm with the holes on the L-bracket.
Page 34
Components Assembly Instructions Contact Left Arm/ Armless...
Page 35
Left Arm/Armless Components Assembly Instructions Contact Connect large base to left arm Place the left arm component on a soft surface, verifying that the two screw holes are facing upward. Gently insert the long base into the arm’s inner slots.
Page 36
Left Arm/Armless Components Assembly Instructions Contact Fasten large base to left arm Using the Allen wrench, fasten the large base to both legs of the left arm component with four hex bolts.
Page 37
Left Arm/Armless Components Assembly Instructions Contact Fasten small leg to large base Using the Allen wrench, fasten the small leg to the large base with two hex bolts. Be sure to leave two threaded holes on the small leg exposed as demonstrated.
Page 38
Left Arm/Armless Components Assembly Instructions Contact Connect large and small bases Gently slide small base into the slotted sections on the Left Arm Module’s large and small legs. Slide base until its pre-drilled holes align with the threaded holes on the legs.
Page 39
Left Arm/Armless Components Assembly Instructions Contact Fasten large and small bases After holes on the bases are aligned with the corresponding threaded holes on each leg, use the Allen wrench to fasten them together with two hex bolts per side.
Page 40
Left Arm/Armless Components Assembly Instructions Contact Drain hole faced down Secure roped backs to large and small bases Insert the lower brackets of the corresponding roped back components into the slots of each base. The Left Arm Module (large base) will require the large roped back and the Armless Module (small base) will require the small roped back.
Page 41
Left Arm/Armless Components Assembly Instructions Contact Attach back supports to roped backs Lower each back support onto the roped backs. The Left Arm Module (large base) will require the left arm back support and the Armless Module (small base) will require the small back support.
Page 42
Left Arm/Armless Components Assembly Instructions Contact Fasten left arm back support to arm and large leg With your Allen wrench, gently fasten left arm back support onto large leg with two hex bolts. Repeat with adjoining side of small back support. Next, align the pre-drilled holes on the left arm with the holes on the L-bracket.
Page 43
Components Assembly Instructions Contact Contact Have a question, comment, feedback? We love hearing from customers. support@hineighbor.com hineighbor.com...