Using The Grill Lighting Instructions - Fisher & Paykel DCS 30 BGC Installation Manual/User Manual

USING THE GRILL
LIGHTING INSTRUCTIONS
LIGHTING INSTRUCTIONS (BH1-30R MODELS ONLY)
Note:
Turn all knobs to "OFF". Turn the main gas supply on. If you smell gas, shut-off gas supply
and call for service.
Grill Lighting Instructions:
Open the grill lid before lighting. The grill knob is connected to the electronic ignition
module. Pushing in on the grill knob will activate the ignition module to get a spark.
Push in and turn the selected burner knob to "SEAR". Release the knob when the burner
lights. If burner does not light in 4 to 5 seconds, turn knob "OFF" and wait 5 minutes
before trying again for any accumulated gas to dissipate.
Grill Match Lighting:
If the burner will not light after several attempts, then the burner can be match
lit. If you've just attempted to light the burner with the ignition, allow 5 minutes
for any accumulated gas to dissipate. Keep your face as far away from the outdoor
appliance as possible and hold a paper book match over the hole located on the top
left for burner on the left, or the right hole for the right burner (Fig. 39a and Fig. 39b).
Push and turn the control knob which is centered on the burner where the lit match
is located, to "SEAR". If the burner does not light in 4 seconds, turn the knob off,
wait 5 minutes and try again.
Once the left or right burner is lit, the adjacent burner can be lit by the cross-lighting method. Light the left or
right burner using the standard or match light procedure. Push and turn the control knob for the adjacent burner
to "SEAR". The gas will be ignited by the adjacent burners flame. If the burner does not light in 4 seconds, turn
knob off, wait 5 minutes and try again.
TO LIGHT THE GRILL BURNER (BCG30-BQ MODELS ONLY):
Open the grill lid before lighting. Turn all knobs to "OFF".
Turn the main gas supply on slowly. If you smell gas, shut-off
gas supply and call for service.
Push and hold the ignition button, turn the selected
burner knob to "SEAR". If burner does not light in 4 to 5
seconds, turn knob "OFF" and wait 5 minutes before trying
again for any accumulated gas to dissipate.
Grill Match Lighting:
If the burner will not light after several attempts then the
burner can be match lit. If you've just attempted to light the
burner with the ignition, allow 5 minutes for any accumulated
gas to dissipate. Keep your face as far away from the grill as
possible and hold and pass a lit, paper book match over the
hole located on the top left for burner on the left, or the right
hole for the right burner (Fig. 40a and Fig. 40b). Push and turn
the control knob which is centered on the burner where the lit
match is located, to "SEAR". If the burner does not light in 4
seconds, turn the knob off, wait 5 minutes and try again.
NOTE:
Improper lighting procedures can cause the LP tank flow control
to activate, resulting in reduced heat output. If this is suspected,
to reset flow control, shut off all burner controls and LP cylinder
valve, wait 30 seconds, then turn LP cylinder valve on extremely
slowly, wait five (5) seconds and push and hold the ignition button
and turn burner valve on to "SEAR".
FIG. 25a
Failure to follow the steps in the order shown may cause the Flow
Limiting Device to activate resulting in extremely low gas ow and
improper operation.
1
HI
2
3
20
Fig. 24a
Fig. 24b
FIG. 25b
WARNING
OFF
All knobs must be in the OFF position before
opening LP tank valve.
Attach regulator hose assembly to tank.
Now open the LP tank valve two (2) full
turns min.