Advertisement
Inventory
Open shipping crate and inventory items included
inside (see Figure 2).
Description:
A. Sleeve Spacers (Bed) ................................ 4
B. Pressure Gauge ......................................... 1
C. Bed Support Rods ...................................... 2
D. Bed Sides ................................................... 2
E. Columns ..................................................... 2
F.
Hydraulic Ram Cylinder .............................. 1
G. Hydraulic Line ............................................. 1
H. Hydraulic Reservoir Assembly ................... 1
I.
Table Plates ................................................ 2
J.
Ram Mounting Plate ................................... 1
K. Cross Beams .............................................. 2
L. Angle Braces .............................................. 4
M. Center Brace .............................................. 1
N. Base Supports ............................................ 2
O. Pump Handle .............................................. 1
C
B
A
F
G
H
I
L
O
Figure 2. Inventory items.
P.
Hardware Bag (not shown)
—Hex Bolts M16-2 x 35 (Cross Beam) ...... 8
—Hex Nuts M16-2 (Cross Beam) ............... 8
—Flat Washers 16mm (Cross Beam) ......... 8
—Lock Washers 16mm (Cross Beam) ....... 8
—Hex Bolts M12-1.75 x 30 (Base) .............. 4
—Hex Nuts M12-1.75 (Base) ...................... 4
—Flat Washers 12mm (Base) .................... 4
—Lock Washers 12mm (Base) ................... 4
—Hex Bolts M10-1.5 x 25 (Base) ............... 8
—Hex Nuts M10-1.5 (Base) ........................ 8
—Flat Washers 10mm (Base) .................... 8
—Lock Washers 10mm (Base) .................. 8
-2-
Qty
D
E
J
K
M
N
—Hex Bolts M10-1.5 x 25 (Tank) ................ 2
—Hex Nuts M10-1.5 (Tank) ........................ 2
—Flat Washers 10mm (Tank)..................... 2
—Lock Washers 10mm (Tank) ................... 2
—Hex Bolts M10-1.5 x 130 (Bed) ............... 4
—Hex Nuts M10-1.5 (Bed) ......................... 4
—Flat Washers 10mm (Bed) ...................... 4
—Lock Washers 10mm (Bed) .................... 4
—Hex Bolts M8-1.25 x 16 (Ram Plate)....... 4
Needed For Setup
Description
Additional People ................................................. 1
Open-End Wrench 13mm .................................... 1
Open-End Wrenches 17, 19, 21mm ............. 2 Ea.
Phillips Head Screwdriver #2 ............................... 1
Mallet .................................................................... 1
Thread-Sealant Tape ...........................As Needed
Mounting Hardware..............................As Needed
Assembly
1.
Lay columns on the ground and connect
base supports and center brace, as shown in
Figure 3, using (4) M12-1.75 x 30 hex bolts,
12mm flat washers, 12mm lock washers, and
M12-1.75 hex nuts.
2.
Attach (2) angle braces to each base support
using (8) M10-1.5 x 25 hex bolts, 10mm flat
washers, 10mm lock washers, and M10-1.5
hex nuts, as shown in Figure 3.
x 8
Angle
Center
Brace
Brace
Figure 3. Center strut and angle braces attached
to base supports and columns.
T1241 20-Ton Hydraulic Press (Mfd. Since 7/20)
Qty
Base
Supports
x 4
Advertisement
