Grizzly T1188 Owner's Manual
  1. Manuals
  2. Brands
  3. Grizzly Manuals
  4. Power Tool
  5. T1188
  6. Owner's manual
Grizzly T1188 Owner's Manual

Grizzly T1188 Owner's Manual

Edgebanding trim router
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
MODEL T1188
EDGEBANDING TRIM ROUTER
OWNER'S MANUAL
(For models manufactured since 06/17)
COPYRIGHT © SEPTEMBER, 2017 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#JH18877 PRINTED IN TAIWAN
V1.09.17

Advertisement

Table of Contents
loading

Related Manuals for Grizzly T1188

Summary of Contents for Grizzly T1188

  • Page 1 (For models manufactured since 06/17) COPYRIGHT © SEPTEMBER, 2017 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #JH18877 PRINTED IN TAIWAN V1.09.17...
  • Page 2 This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.

  • Page 3: Section 1: Safety

    Operating tools in when operating or observing machinery to these areas greatly increases risk of acci- reduce the risk of eye injury or blindness dents and injury. from flying particles. Everyday eyeglasses are not approved safety glasses. Model T1188 Edgebanding Trim Router...

  • Page 4: Securing Workpiece

    FORCING TOOLS.. Use right tool for job, forming the intended operation, stop and do not force it. It will do job safer and using the machine! Contact our Technical better at rate for which it was designed. Support at (570) 546-9663. Model T1188 Edgebanding Trim Router...
  • Page 5 Always consider safety first, as it applies to your individual working conditions. Use this and other machinery with caution and respect. Failure to do so could result in serious personal injury, damage to equipment or poor work results. Model T1188 Edgebanding Trim Router...

  • Page 6: Polarized Plug

    The extension cord must also contain a ground wire and plug pin. • DO NOT use an extension cord that 1-15 Plug has cuts, exposed wires, bent/missing Neutral prongs, or other damage. Figure 1. Typical 1-15 plug and receptacle. Model T1188 Edgebanding Trim Router...

  • Page 7: Section 2: Introduction

    This tool presents serious injury ⁄ " Collet Size ..........hazards to untrained users. Read Min. Inner Radius ........1" through entire manual to become Max. Bit Diameter ........1 ⁄ " familiar with controls and operations before using! Model T1188 Edgebanding Trim Router...
  • Page 8 Safety Cover Clear Bit Guard 1" Dust Port Figure 2. Router component identification. This tool presents serious injury hazards to untrained users. Read through entire manual to become familiar with controls and operations before using! Model T1188 Edgebanding Trim Router...

  • Page 9: Section 3: Setup

    Inventory To test run trim router: 1. Clear all setup tools away from trim tool. Model T1188 Inventory (Figure 3) A. Trim Router (Not Shown) ....1 2. Connect tool to power supply. B. Collet Wrench 22mm ......1 C.

  • Page 10: Section 4: Operations

    3. Pull tool with even pressure along edge before setting it down. of banded workpiece to remove excess edgebanding. Note: Additional touch-up sanding may be required for a smooth surface. Model T1188 Edgebanding Trim Router...

  • Page 11: Routing Tips

    DO NOT start routing at a corner. can fly out of your hands, causing Starting at a corner may cause serious personal injury. the router to grab, damaging the workpiece corner, and possibly causing personal injury. Model T1188 Edgebanding Trim Router...
  • Page 12 Unplug tool and make sure switch is OFF before inserting or remov- 5. Re-install base plate to motor. ing bit, making adjustments, or per- forming maintenance or service. Never make adjustments while tool is running. Model T1188 Edgebanding Trim Router...
  • Page 13 (see Figure 12). Each full rotation rais- es/lowers the bit 2mm ( ⁄ "). Note: The scale on the Model T1188 is not calibrated to any specific point. Only use it for reference when making incremental changes. Unplug tool and make sure switch...
  • Page 14 Tool Figure 13. T1189 Dual-End Cutter. Base Plate Figure 15. Aligning trim router to The T1188 also converts for end-trimming workpiece corner. operation by using the built-in edging tool as a pivot point for vertical trimming. To end-trim with router: 1.

  • Page 15: Section 5: Accessories

    To reduce this a time. risk, only install accessories recom- mended for this tool by Grizzly. H4978 Refer to our website or latest cat- alog for additional recommended accessories.

  • Page 16: Section 6: Maintenance

    Figure 20. Motor brush location. Motor brushes will eventually wear out over time. If the motor will not run, makes 5. Re-install brushes and motor cover. squealing or grinding noises, or perfor- mance is dramatically decreased, check motor brushes. Model T1188 Edgebanding Trim Router...
  • Page 17 PT1188031 COMPRESSION SPRING PT1188014 COLLET 1/4" PT1188032 MAIN BODY PT1188015 COMPRESSION SPRING PT1188033 MODEL NUMBER LABEL PT1188016 ROUTER BIT 1/4" ROUND-OVER PT1188034 MACHINE ID LABEL PT1188017 CARBON BRUSH HOLDER PT1188035 QR CODE PT1188018 CARRYING CASE Model T1188 Edgebanding Trim Router...

  • Page 18: Warranty And Returns

    WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.

  • Page 19: Warranty Card

    ____70+ How long have you been a woodworker/metalworker? ____0-2 Years ____2-8 Years ____8-20 Years ____20+ Years How many of your machines or tools are Grizzly? ____0-2 ____3-5 ____6-9 ____10+ Do you think your machine represents a good value? ____Yes ____No...

Table of Contents