Table of Contents
Advertisement
Installation Requirements
‒
A location with sufficient space
‒
A location with good ventilation
‒
A location with a flat, even surface
‒
A location able to fully support the weight of the machine
Do not install the machine in the following locations, as this may result in
damage to the machine.
‒
A location subject to dramatic changes in temperature or humidity
‒
A location subject to condensation
‒
A poorly ventilated location (If you use the machine for a long time or
to perform a large amount of printing in a poorly ventilated room, the
ozone or other odors generated by the machine may create an
uncomfortable working environment. In addition, chemical particles
are dispersed during printing; therefore, it is important to provide
adequate ventilation.)
‒
A location near equipment that generates magnetic or
electromagnetic waves
‒
A laboratory or location where chemical reactions occur
‒
A location exposed to salt air, corrosive gases, or toxic gases
‒
A location, such as on a carpet or mat, that may warp from the weight
of the machine or where the machine is liable to sink
Installation Space
Required installation space
Front View
1279 mm
Paper cassette
100 mm
100 mm
100 mm
100 mm
Maintenance and Inspections
‒
Follow the instructions in the caution label attached to this machine.
‒
Avoid shaking or applying a shock to this machine.
‒
To prevent the paper jam, do not turn the power ON/OFF, open/close
the operation panel or rear cover, and load/unload paper in the middle
of printing operation.
‒
Be sure to remove the toner cartridge from the machine when
transporting the machine.
‒
To avoid exposing the toner cartridge to light, place it in the protective
bag included with this machine or wrap it in a thick cloth.
‒
Clean this machine regularly. If this machine becomes dusty, it may
operate improperly.
‒
Use a modular cable of 3 m or shorter in length.
‒
The communication may become unavailable depending on the
condition of local environment, such as when the total resistance value
of telephone line and this machine exceeds 1,700 Ω. In this case,
contact your local authorized Canon dealer or the Canon help line.
‒
The repairing parts and toner cartridges for the machine will be
available for at least seven (7) years after production of this machine
model has been discontinued.
Contacting Service Center
When you have a problem with your machine and you cannot solve it,
even if you refer to the manuals or online help, please contact your local
authorized Canon dealer from whom you purchased the equipment (if
under warranty), or with whom you have a servicing contact.
24
Legal Notices
Model Names
F158002 (MF5870dn)
International ENERGY STAR Program
Laser Safety Information
Laser radiation could be hazardous to the human body. For this reason,
(mm)
laser radiation emitted inside this equipment is hermetically sealed
within the protective housing and external cover. No radiation can leak
from the machine in the normal operation of the product by the user.
100 mm
This machine is classified as a Class 1 Laser Product under IEC60825-1:
2007 and EN60825-1: 2007.
220–240 V Model
Feeder
The label shown below is attached to the laser scan unit on the machine.
This machine has been classified under IEC60825-1:2007 and EN60825-1:
2007 and conforms to the following classes:
CLASS 1 LASER PRODUCT
LASER KLASSE 1
APPAREIL Á LASER DECLASSE 1
APPARECCHIO LASER DI CLASSE 1
PRODUCTO LÁSER DE CLASE 1
APARELHO A LASER DE CLASSE 1
LUOKAN 1 LASER-TUOTE
LASERPRODUKT KLASS 1
Use of controls, adjustments, or performance of procedures other than
those specified in the manuals for the machine may result in hazardous
radiation exposure.
As an ENERGY STAR® Partner, Canon Inc. has
determined that this product meets the ENERGY
STAR Program for energy efficiency.
The International ENERGY STAR Office Equipment
Program is an international program that
promotes energy saving through the use of
computers and other office equipment.
The program backs the development and
dissemination of products with functions that
effectively reduce energy consumption. It is an
open system in which business proprietors can
participate voluntarily.
The targeted products are office equipment, such
as computers, displays, printers, facsimiles, and
copiers. The standards and logos are uniform
among participating nations.
Advertisement
Table of Contents
