Table of Contents
Advertisement
7.2
Power Supply
Refer to figure
Figure 7-4
platform.
Display power
PFC
7.2.1
Power Supply Unit
All power supplies for TV's that are using a LED back lit LCD
panel are under repair policy. When defective, first check the
main fuse of the power board. Always replace a defective fuse
with one with the correct specifications! This part is available in
the regular market.
Consult the Philips Service web portal for the order codes of the
boards.
Important delta's with the xxHFL3XXXD/10 series platform are:
•
New power architecture for LED backlight (PSL, PSLS,
PSDL)
•
"Boost" signal is now a PWM-signal + continuous variable.
The control signals are:
•
Stand-by
•
Inverter "on/off"
•
DIM (PWM) (not for PSDL)
In this manual, no detailed information is available because of
design protection issues.
The output voltages to the chassis are:
•
+5V-STANDBY (Stand-by mode only)
•
+12V (on-mode)
•
+Vsnd (+24V) (audio power) (on-mode)
•
+24V (bolt-on power) (on-mode)
•
Output to the display; in case of
- IPB: High voltage to the LCD panel
- PSL and PSLS (LED-driver outputs)
- PSDL (high frequent) AC-current.
7.2.2
Diversity
The diversity in power supply units is mainly determined by the
diversity in displays.
for the power architecture of this
Ac-input + Mains filter
Figure 7-4 Power Architecture ( for 30xx series)
Circuit Descriptions
Platform power
BL-ON/OFF
DIM
12V
24V
5V
Low stby
power
AC IN
The following displays can be distinguished:
•
CCFL/EEFL backlight: power board is conventional IPB
•
LED backlight:
- side-view LED without scanning: PSL power board
- side-view LED with scanning: PSLS power board
- direct-view LED without 2D-dimming: PSL power board
- direct-view LED with 2D-dimming: PSDL power board.
PSL stands for Power Supply with integrated LED-drivers.
PSLS stands for a Power Supply with integrated LED-drivers
with added Scanning functionality (added microcontroller).
PSDL stands for a Power Supply for Direct-view LED backlight
with 2D-dimming.
7.2.3
Connector overview
Table 7-1 Connector overview
no.
Descr.
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
back to
div. table
TPM9.2HE LA
7.
AMP
24V
Platform
MTK5366
CN7001
/CN700
1 power- PCB
Connector
32HFL30X7
42HFL30x7
CN8101
CN9302
CN8503
to panel
to SSB
to panel
CN8101
CN9304
CN8503
VLED
P_OK
LED-11
n.c.
+5.2V
LED-16
LED3
+5.2V
LED-12
LED6
PS_ON
LED-15
LED2
+24V
LED-14
n.c.
+24V
-
n.c.
GND
VLED
LED5
GND
-
LED1
GND
-
LED4
+12V
-
n.c.
+12V
-
VLED
DIM
-
-
ON/OFF
-
EN 35
LVDS
12V
19240_202_120224.eps
120925
CN902
to SSB
CN902
P_OK
+5.2V
+5.2V
PS_ON
+24V
+24V
GND
GND
GND
+12V
+12V
DIM
ON/OFF
2013-May-30
Advertisement
Table of Contents
