Furuno FAR-2228-BB Operator's Manual page 250

APPENDIX 1 MENU TREE
1
3 NAV TOOLS
* 1 : Shown for B/W-types only.
* 2 : Shown for IMO/A/R types only.
3
* : Shown for A/B/W-types only.
* 4 : Shown for IMO/A/B/R-types only.
5
* : Shown for W-types only.
6
* : Not shown for W-types.
* 7
: Shown for B-types only.
4 ALERTS 2 WATCH ALERT (OFF, 6min, 10min, 12min, 15min, 20min)
3 ALERT VOLUME (OFF*
4 ANCHOR WATCH (OFF, ON; 0.00NM to 9.99NM)
5 TARGET ALARM
5 TT•AIS 2 ACQUISITION
ZONE
3 TRIAL
MANEUVER
2
1
(Continued on next page)
AP-4
4
2 PI LINES* 2 PI LINE BEARING (REL, TRUE)*
3 SET MAXIMUM PI LINES (1, 2, 3, 6)
4 PI LINE MODE (PARALLEL, PERPENDIC)
5 RESET PI LINES
6 TRUNC RANGE1 (OFF, ON; 0.000NM to 24.000NM)
7 TRUNC RANGE2 (OFF, ON; 0.000NM to 24.000NM)
2 PI LINES* 5 2 SET MAX PI 1•3 LINES (2, 3, 6)
3 SET MAX PI 1•3 LINES (2, 3, 6)
4 PI LINE MODE (PARALLEL, PERPENDIC)
5 RESET PI LINES
3 EBL • VRM • 2 EBL1 (REL, TRUE)
1
CURSOR SET*
3 EBL2 (REL, TRUE)
4 VRM1 (NM, km, SM, kyd)
5 VRM2 (NM, km, SM, kyd)
6 EBL OFFSET BASE (STAB GND, STAB HDG,
7 VRM TTG (OFF, 1, 2, 1and2)
8 VRM OFFSET (OFF, LINK EBL)
9 CURSOR
0 NET
CURSOR
3 EBL • VRM • 2 EBL OFFSET BASE (STAB GND, STAB HDG,
2
CURSOR SET*
3 VRM TTG (OFF, 1, 2, 1and2)
4 VRM OFFSET (OFF, LINK EBL)
5 EBL•CURSOR BEARING (REL, TRUE)
6 CURSOR L/L ALIGN (OFF, ON)
4 RANGE RINGS (OFF, ON)
3 , LOW, MID, HIGH)
2 ALR1 MODE (IN, OUT)
3 ALR2 MODE (IN, OUT)
4 LEVEL (1, 2, 3, 4)
2 AZ/ALR SELECT (ACQUISITION ZONE, TARGET ALARM ZONE)
3 TGT TYPE TO ACQUIRE (TT AND AIS, TT ONLY)*
4 AZ STABILIZATION (STAB HDG, STAB NORTH)
5 AZ POLYGON (OFF, STAB GND, STAB HDG, STAB
6 CHECK AREA SETTING (PORT, STBD, BOW, STERN;
2 TRIAL MANEUVER (OFF, STATIC, DYNAMIC)
3 TRIAL SPEED RATE (0kn to 99kn, 0.00kn/s to 9.99kn/s)
4 TRIAL TURN RATE (0kn, 0.0°/s to 99.9°/s)
5 TRIAL TARGET DATA (ACTUAL, TRIAL)*
7
* 6
* 6
STAB NORTH)
2 CURSOR BEARING (REL, TRUE)
3 CURSOR RANGE (NM, km, SM, kyd)
4 CURSOR SIZE (SMALL, LARGE)
5 CURSOR L/L ALIGN (OFF, ON)
2 NET CURSOR DISPLAY (OFF, ON)
3 FRONT HALF LENGTH (0.0m to 3000.0m)
4 REAR HALF LENGTH (0.0m to 3000.0m)
5 NET WIDTH (0.0m to 3000.0m)
6 ROTATE STEP (360°, 32POINT)
7 WARP LENGTH (Displays net warp)
STAB NORTH)
NORTH, AROUND CHECK AREA*
0.0NM to 16.0NM, 1.0NM)*
3
* 6
1
1 )
1