How To Maintain - Hitachi R-SF6800Z Instructions For Use Manual

)

How to maintain

Vacuum compartment case
How to remove 取出方法
Completely pull out the door towards you.
往身前方向把門完全的打開。
Lightly hold and lift up the front side of the
1
vacuum compartment case to release the
case from the catch on the door.
握住真空室盒的前部輕輕向上抬起，從箱門的
掛鉤上放開真空室盒。
Vacuum Vacuum
compartment compartment
case case
真空室盒 真空室盒
Catch Catch
掛鉤 掛鉤
Slide the vacuum compartment case towards
2
you to pull it out.
往身前方向拉出
真空室盒。
Be sure to remove the vitamin
cassette when washing the
vacuum compartment case.
清洗真空室盒時，請先拆下維生素盒。
How to fix
Slide the vacuum compartment case into the
1
main unit.
將真空室盒推入主體。
2
Align the front side of the vacuum
compartment case with the catch on the
door and then fix the case.
將真空室盒前部對準箱門上的掛鉤，固定好
真空室盒。
Vacuum Vacuum
compartment compartment
case case
真空室盒 真空室盒
Fit in Fit in
裝入 裝入
CAUTION
注 意
。
__R-SF6800Z.indd 23
(Monthly maintenance)
真空室盒
如何安裝
If water drops such as dew are deposited inside the vacuum compartment, wipe and
clean it with dry cloth, etc.
Using the detergents etc. other than lukewarm water may cause damage, deform or
discolor of the parts, and as a result, it may be impossible to keep the vacuum.
Juicy food may freeze when the surrounding temperature is low.
Do not remove any parts other than the Vacuum Case and Vacuum Packing.
Wipe off spilled water or food soup immediately.
如果真空室內部積有冷凝水珠等，請用乾布擦乾淨。
使用溫水以外的洗潔劑等會使部件破損・變形・變色，並致使不能保持真空狀態。
周圍溫度低的時候，水分多的食品會凍結。
真空冷凍盒和真空包裝以外，會有可能凍結。
水或食品汁弄灑了的時候，請儘快擦乾淨。
保養方法（每月一次）
Vacuum packing
Pull out the door and remove the vacuum
1
compartment case. (Refer left column)
往身前方向打開箱門，取出真空室盒。(參閱左欄)
Wipe the vacuum packing and the vacuum
2
packing receiving portion with a soft cloth
damped with lukewarm water.
用柔軟的布蘸溫水擦拭真空密封墊及其承托部。
Vacuum Packing
contact part
與真空墊接觸部分
Vacuum Packing
(installed on the back side of the door)
真空墊(安裝在門後面)
If the dirt on the vacuum packing could not come
off after wiping, remove it and wash with water.
如果真空密封墊上的污垢無法擦掉，請將其取出
後用水清洗。
3
Hold the protrusion on the vacuum packing,
which is located on your upper right, with your
hand carefully and remove the vacuum packing.
用手握住在你右上方的真空密封墊上的突起，
仔細拆下真空密封墊。
Protrusion
突起
4
Wash the dirty area with a soft sponge, etc. and
water, then wipe dry.
用海綿等柔軟的材料和水清洗污垢，然後用乾布
擦乾淨。
Wipe off the dirt in the vacuum packing groove
5
located on the door.
將箱門上真空密封墊凹槽中的污垢擦乾淨。
6 Align the protrusion on the vacuum packing with
the mark on the door and attach the packing firmly.
真空密封墊上的突起對準箱門上的標記牢牢固定。
Protrusion
突起
7
Fix the vacuum compartment case (refer left column).
安裝真空室盒（參閱左欄）。
(Continue)
（繼續）
真空密封墊
Marking 標記
真
空
室
真
空
チ
ル
ド
︵
繼
續
︶

2009/10/26 11:17:09