Sony HDV HVR-1500 Operating Instructions Manual page 81

VIDEO CONTROL [Video]: Settings related to video
control
HD PROCESS CONTROL
[> HD Process]
SYNC PHASE [> Sync
Phase]: Adjust the sync
phase.
INPUT BLANK [> Input blnk]
Note
Displayed only when the
system frequency is set to 50i.
AUDIO CONTROL [Audio]: Settings related to audio
control
REC MODE [> REC mode]: Select the audio recording mode. *2 CHANNEL (48kHz) [>> 2 ch]: 2-channel, 48-kHz mode
INPUT ARRANGE [> Input arng]: Make settings for input
audio mixing.
Notes
• When, in 4-channel mode, analog audio is selected for all
four channels (channels 1/2 and 3/4), the same analog
audio signals are recorded on channels 1 and 3 and on
channels 2 and 4, respectively. That is, the analog signal
recorded on channel 1 is also recorded on channel 3 and
the analog signal recorded on channel 2 is also recorded on
channel 4.
You can adjust the audio level on each of the four channels
separately using the REC/PB LEVEL control knobs with the
VARIABLE switch set to REC.
• For an i.LINK input selection, this setting is invalid.
ADJ RANGE [>> Adj range]:
Select the adjustment
range for video gain and
chrominance gain.
VIDEO GAIN [>> V gain]:
Control the video output
level.
CHROMA GAIN [>> C gain]:
Control the chrominance
output level.
CHROMA PHASE [>> C
phase]: Control the
chrominance phase.
SETUP LEVEL [>> Setup
lev]: Control the setup
level.
SYNC PHASE [>> Sync
phs]: Control the
SYNC+SC phase.
SUB CARRIER [>> SC
phase]: Control the
subcarrier phase.
LINE 335 [>> Line 335]:
Select whether to blank
line 335, or to output it as
part of the video signal.
Description of settings
*–3 to +3(db) [>>> –3/+3]: –3 dB to +3 dB
WIDE [>>> wide]: –∞ to +3 dB
000 [>>> 000] to 3FF [>>> 3FF]
Factory default setting: *200H
000 [>>> 000] to 3FF [>>> 3FF]
Factory default setting: *200H
00 [>>> 000] to FF [>>> FF]
Factory default setting: *80H
000 [>>> 000] to 3FF [>>> 3FF]
Factory default setting: *200H
000 [>>> 000] to 3FF [>>> 3FF]
Factory default setting: *Adjusted value at factory or 200H
000 [>>> 000] to 3FF [>>> 3FF]
Factory default setting: *Adjusted value at factory or 200H
*BLANK [>>> blank]: Blank.
THROUGH [>>> through]: Output as a video signal.
Description of settings
4 CHANNEL (32kHz) [>> 4 ch]: 4-channel, 32-kHz mode
Set the channels on which to record the input audio signals as
follows.
(1) Use the Mm</A ,/B buttons to move the cursor and
the SET (YES) button to toggle the setting on and off.
(2) To save the settings, press the MENU button to return to the
previous screen, then press the SET (YES) button.
Example settings:
A U D I O I N P U T S O U R C E
A R R A N G E
i n 1 i n 2 i n 3 i n 4
- - - - - - - - - - - - - - - - -
c h 1 : * o n
c h 2 : o n o n
c h 3 : o n
c h 4 o n
O N / O F F : S E T K E Y
T O M E N U : M E N U K E Y
1Input audio channel 1 ("CH1") is recorded on audio channel
1 ("CH1") on tape.
2Input audio channels 2 and 4 ("CH2" and "CH4") are
recorded mixed on audio channel 2 ("CH2") on tape.
3Input audio channel 4 ("CH4") is recorded on audio channel
3 ("CH3") on tape.
4Input audio channel 3 ("CH3") is recorded on audio channel
4 ("CH4") on tape.
1
2
3
4
81
Menu Contents