Sony HDV HVR-1500 Operating Instructions Manual page 48

Setting the current tape position as point A
or B
POWER
INPUT SELECT
i.LINK VIDEO CH1 1/2 CH2 3/4
OVER
0
REC/PB LEVEL
-12
1 2 3 4
-20
-30
-40
-60
1
CH
MONITOR
LEVEL VARIABLE
SELECT EDIT MODE
REC INHI
REC
PRESET
PB
PHONES CONTROL-S REW PLAY
Buttons used for setting
the current tape position
as point A
While holding down the SET (YES) button in the menu
control section, press the </A or ,/B button. The
timecode value of the current tape position is set as point
A or B, and a message "A set" or "B set" is displayed for
0.5 second in the time counter display.
Once set, the point A or B timecode value is held in the
non-volatile memory of the unit until changed. It is not lost
when the unit is powered off.
Note
When setting point A or B, you can only use a timecode
value. Even when CNT is selected with the COUNTER
SELECT button, you cannot use a CNT value to set point
A or B.
To check the point A or B timecode value
Press the </A or ,/B button in the menu control
section. While the button is held down, the point A or B
timecode value is displayed on the monitor screen and in
the time counter display.
If you hold down the </A and ,/B buttons
simultaneously, the value shown is the point B timecode
value minus the point A timecode value. If the point A
timecode value is greater than the point B timecode value,
a minus sign (–) is shown before the value.
Inputting timecode values for points A and
B
Using the following procedure, you can modify the
timecode value for point A or B.
48
Playback
EJECT
LOCAL
9PIN
i.LINK
OVER
REPEAT 1080 525 HDV DVCAM
(DV)
DISPLAY MENU ASSIGN RESET(NO)
TC
2 TC VITC 44.1K
CH SET(YES)
COUNTER PRESET
01:23:45:15
SELECT
F FWD STOP REC
A B
MENU ASSIGN RESET(NO)
TC
PRESET SET(YES)
A B
Buttons used for setting
the current tape position
as point B
MENU ASSIGN
1,15
TC
PRESET
A
8,11
5,7,9,12
1
Press the MENU button.
The following menu display appears.
S Y S T E M M E N U
S E T U P M E N U
A U T O F U N C T I O N
H O U R S M E T E R
Monitor screen
2
With SETUP MENU selected, press the ,/B
button.
The display changes as follows.
S E T U P M E N U
O P E R A T I O N A L F U N C T I O N
D I S P L A Y C O N T R O L
T I M E C O D E
S E T U P B A N K O P E R A T I O N
S Y S T E M S E L : J
M E N U G R A D E : B A S I C
Monitor screen
3
With OPERATIONAL FUNCTION selected, press
the ,/B button.
The display changes as follows.
S E T U P M E N U
O P E R A T I O N A L F U N C T I O N
R E P E A T F U N C T I O N
A U T O E E S E L E C T
L O C A L E N A B L E : S T P & E J
R E C F O R M A T
Monitor screen
4
With REPEAT FUNCTION selected, press the ,/B
button.
The contents of the REPEAT FUNCTION menu item
are displayed.
RESET(NO)
SET(YES)
13
12
B
2,3,4,6,
10,11
Setup menu
Time counter display
Operational
Time counter display
> REP FUNC
Time counter display