Adapting Settings For Heating System Automatic; Mode; Heating Temperature Settings; Adapting The Time Program For Heating System Automatic Mode - Bosch HPC 400 Operating Instructions Manual

5.2 Adapting settings for heating system
automatic mode
Menu: Heating/Cooling
Optimised operation (without a time program) is active for
each heating circuit by default. If required, the user can change
the setting and select the time-dependent automatic mode. A
constant room temperature value can be specified for cooling

mode.

Heating circuit 1 ... 4
If more than one heating circuit has been installed and
configured, the settings for heating circuits 1 ... 4 are changed
in the same way as for systems with one heating circuit.
However, changes are valid only for the selected heating
circuit. Assigning unique names to heating circuits makes it
much easier to make the right selection.

5.2.1 Heating temperature settings

The temperatures for the various operating modes can be set in
this menu. Depending on whether the user interface is working
in automatic mode or in optimised operation, the temperatures
have an effect on how the system is controlled.
Menu: Temperature settings
Menu item description
Heating If automatic mode is active, the room
temperature is maintained at the value
set here for the specified time slots with
the Heating operating mode.
Setback If automatic mode is active and a
temperature has been set here, the room
temperature is maintained at the value
set here for the specified time slots with
the Setback operating mode. If heating is
switched off here, no heating will occur
during these time slots.
Cooling If a heating/cooling circuit is installed, the
room temperature is maintained at the
value set here for the Cooling operating
mode.
Table 10 Heating system temperature settings
5.2.2 Adapting the Time program for heating system
automatic mode
The time program is only active for the heating system if
automatic mode is active ( Chapter 4.2, page 8).
To set the same switching times for multiple days of the week:
▶ Set switching times for a group of days, e.g.
Mon-Sun or Mon-Fri.
HPC 400
CLIMATE CONTROL SYSTEMS
▶ Adjust the time program for the specific days of the week
for which different settings are required under Monday ...
Sunday (detailed description  Tab. 13, page 16).
Menu: Time program
Menu item
Activate time
program
My time
program 1
Reset prog.
My time
program 2
Reset prog.
Rename heating
circuit
Rename time
program
Table 11 Time program settings for heating
The time program ensures automatic changeover between
operating modes at defined switching times. The user interface
has two time programs for each heating circuit. Two switching
times per day can be programmed, each with an operating
mode. The default settings for the time programs provide lower
heating overnight. Optimized mode provides the most
economic heating for both day and night.
If the settings, temperatures or switching times of the time
program do not meet your needs, you can adapt the time
program. If you do not require heating overnight, speak to your
contractor. He has access to additional settings for configuring
setback mode.
VOGEL NOOT
&
Working with the main menu | 15
description
Activating automatic mode triggers
control of the room temperature
according to the settings in the selected
time program (My time program 1 or My
time program 2).
2 switching times can be set for each day
or group of days. One of the two
operating modes can be assigned to each
switching time in automatic mode. The
minimum duration of a time slot between
two switching times is 15 minutes.
Here My time program 1 can be reset to
the default settings.
 My time program 1
Here My time program 2 can be reset to
the default settings.
The name of the selected heating circuit
can be customised here (only available if
more than one heating circuit is
installed). This helps to select the correct
heating circuit, e.g. "underfloor heating
system" or "attic apartment". The names
are set by default to Heating circuit 1 ...
4 ( Tab. 14, page 18).
The names of the time programs can be
changed in the same way as the names of
the heating circuits. This helps to select
the correct time program, e.g. "family" or
"night shift".
6 720 817 986 (2015/07)