Trane RTAF-SVX001K-EN Manual page 51

AFD Drive Programming
Field replacement drives must be programmed via the
keypad interface. Program parameters sequentially by ID
values as defined in tables below.
Table 24. Non-compressor specific parameter settings
ID Description
0-03 Region Settings
0-20 Display Line 1.1 Small
0-24 Display Line 3 Large
0-40 [Hand on] Key on LCP
0-41 [Off] Key on LCP
0-60 Main Menu Password
0-61 Access to Main Menu w/o Password
1-03 Torque Characteristics
1-21 Motor Power [HP]
1-22 Motor Voltage
1-23 Motor Frequency
1-24 Motor Current
1-25 Motor Nominal Speed
1-71 Start Delay
1-73 Flying Start
1-78 Compressor Start Max Speed [Hz]
1-79 Compressor Start Max Time to Trip
1-82 Min Speed for Function at Stop [Hz]
1-87 Trip Speed Low [Hz]
3-02 Minimum Reference
(b)
3-03 Minimum Reference
3-41 Ramp 1 Ramp Up Time
3-42 Ramp 1 Ramp Down Time
3-82 Starting Ramp Up Time
4-10 Motor Speed Direction
4-12 Motor Speed Low Limit [Hz]
4-18 Current Limit
Table 25. Compressor-specific parameter settings, 115 to 215 tons — 60Hz
Parameters
ID Description 460V 380V 575V 460V 380V 575V 460V 380V 575V 460V 380V 575V 460V 380V 575V
1-21 Motor Power (hp) 86
1-22 Motor Voltage (V) 460V
1-24 Motor Current (A) 91A
Motor Nominal
1-25 3461
Speed (rpm)
Max Output
4-19 61
Frequency (Hz)
Voltage at Main
14-11 391V
Fault (V)
(a) 400V/50 Hz units use 380V/60Hz compressor settings.
RTAF-SVX001K-EN
Setting
[1] North American
[1612] Motor Voltage
[1617] Speed (rpm)
[0] Disabled
[0] Disabled
999
[1] LCP: Read-only
[0] Compressor Torque
(a)
See table below
See table below(a)
60Hz
See table below(a)
See table below(a)
0s
[0] Disabled
30Hz
10s
10Hz
25Hz
30Hz
See Table 26
5s
5s
3s
[0] Clockwise
30Hz
128.4%
L1 L2
86 86 102 102
380V 575V 460V 380V
110A 73A 109A 132A
3460 3461 3459 3466
61 61 61 61
323V 489V 391V 323V
Table 24. Non-compressor specific parameter settings
(continued)
ID Description
4-19 Max Output Frequency
4-
Motor Speed High Limit [Hz]
14(b)
5-12 Terminal 27 Digital Input
5-13 Terminal 29 Digital Input
5-40.0 Function Relay 1
5-40.1 Function Relay 2
5-41.0 On Delay, Relay 1
5-41.1 On Delay, Relay 2
5-42.0 Off Delay, Relay 1
5-42.1 Off Delay, Relay 2
6-10 Terminal 53 Low Voltage
6-14 Terminal 53 Low Ref./Feedb. Value
6-
Terminal 53 High Ref./Feedb. Value
15(b)
6-50 Terminal 42 Output
14-03 Overmodulation
14-10 Mains Failure
14-11 Mains Voltage at Mains Fault
14-20 Reset Mode
14-30 Current Lim Ctrl. Proportional Gain
14-31 Current Lim Ctrl. Integration Time
14-50 RFI Filter
14-51 DC Link Compensation
22-75 Short Cycle Protection
22-76 Interval Between Starts
(a) For unit sizes 115 to 215, see
see Table 26.
(b) Parameter for 230 to 520 ton units only.
(a)
M3
102 122 122 122
575V 460V 380V 575V
87A 128A 154A 101A
3461 3502 3505 3503
61 61 61 61
489V 391V 323V 489V
Installation Electrical
Setting
See table
See
[2] Coast Inverse
[0] No Operation
[5] Running
[3] Drive Rdy/Rem Ctrl
See
[133] Motor Cur. 4-
[0] Off
[4] Kinetic Back-up
See table
[1] Automatic Reset x 1
[0] Off
[1] On
[1] Enabled
Table 25. For unit sizes 230 to 520 tons,
M4
144 144 144 177
460V 380V 575V 460V
151A 182A 120A 183A
3494 3494 3494 3494
61 61 61 61
391V 323V 489V 391V
below(a)
Table 26
1s
1s
1s
1s
2V
30Hz
Table 26
20mA
below(a)
25%
1s
60s
N3
177 177
380V 575V
221A 146A
3495 3493
61 61
323V 489V
51