Punch-In Recording - Casio WK-1600 User Manual

RECORD
To use real-time recording in Tracks 2 through 6
NOTE
If you are performing real-time recording in Tracks 2 through 6 immediate-
ly after you finished real-time recording in Track 1, skip steps 1 and 2 of
the following procedure.
1.
Press the SONG button once.
• This causes the indicator lamp above the SONG button to
light.
2.
Select the user song area to which you want to record.
• Use [+] and [–] to select User Song Area 0 (SG0) or User Song
Area 1 (SG1).
• Change Mixer settings for the channel if you want. The Mix-
er settings you make for the channel are copied to applica-
ble track during recording.
3.
Press the RECORD button to enter record standby.
• The REC indicator appears, and the frame around the cur-
rently selected channel (track) flashes on the display.
T U N E 1
• Channels CH 11 through CH 16 of the level meter show which
tracks already contain recorded data. See "Level Meter Dur-
ing Record Operations" on page E-44 for details on how to
read the level meter.
4.
Select the track to which you want to record.
• Use CHANNEL buttons CH12 (Track 2) through CH16 (Track
6) to select the track you want.
CH 11 CH 12
TR1 TR2
5.
Make any tone setting you want.
6.
Press the START/STOP button to start recording.
• At this time the REC indicator stops flashing.
• The metronome normally sounds during recording. If you
want to turn off the metronome, use the procedure under
"Metronome Setting (1)" on page E-46.
7.
Play the notes you want to record on the keyboard.
E-42
WK-1800/1600(E)-39~47
SONG
FULL RANGE
CHORD MAX
FINGERED
CASIO CHORD
MIN
EXTERNAL CH 1 CH 2 CH 3 CH 4
SONG PATTERN
INTERNAL UPPER1 UPPER2 LOWER1 LOWER2 ACC VOL.
BANK
START/STOP
CH 13 CH 14 CH 15 CH 16
TR3 TR4 TR5 TR6
Page 42
CHANNEL
7 8
4 5
1 2
/NO
CH 5 CH 6 CH 7 CH 8 CH 9 CH 10 CH 11 CH 12 CH 13 CH 14 CH 15 CH 16 PARAMETER RESET: 0
MAIN MANU/ DELETE
CHORD1 CHORD2 CHORD3 BASS RHYTHM TR1 TR2 TR3 TR4 TR5 TR6 CHANNEL VOLUME:
SUB MANU/
CHANNEL SELECT:
STORE
ENTER
8.
After you are finished, press START/STOP to stop re-
cording.
• The REC indicator disappears from the display when record-
ing is stopped.
9.
At this point you can repeat steps 3 through 8 for oth-
er tracks, if you want.

Punch-in Recording

Note that the procedure you use for Track 1 is different from that for
Tracks 2 through 6.
PREPARATION
• Determine the tones that you want to use.
• Set the tempo that you want to use during recording.
NOTES
• You can change tone and rhythm while recording is in progress.
• The previously recorded rhythm pattern is automatically selected at first,
but you can change the rhythm during punch-in recording. Changing
the rhythm during punch-in recording, however, may cause the metro-
nome display and rhythm beat to be out of synch with the rhythm that is
playing.
• The tempo you use for recording does not affect the tempo of the play-
back. This means you can record at a very slow tempo for easy play,
and then speed up the tempo for playback.
To use punch-in recording in Track 1
1.
Press the SONG button once.
• This causes the indicator lamp above the SONG button to
light.
2.
Select the user song area that contains the song whose
contents you want to change using punch-in record-
ing.
• Use [+] and [–] to select User Song Area 0 (SG0) or User Song
Area 1 (SG1).
3.
Press the RECORD button to enter record standby.
• The REC indicator appears, and the frame around the CH11
(Track 1) flashes on the display.
T U N E 1
03.7.31, 5:21 PM
AMP ENVELOPE
9 DECAY
SUSTAIN
6
PITCH ENVELOPE
00 FLAT
3
01-17 VIBRATO
/YESS
[+]/[
18-45 OTHERS –]
T UNE 1
733A-E-044A
Adobe PageMaker 6.5J/PPC