Operational Precautions - Toto WASHLET SW4547AT60 Instruction Manual

Safety Precautions
Grounding Instructions
This product should be grounded. In the event of an electrical short circuit, grounding
reduces the risk of electric shock by providing an escape wire for the electrical current.
The plug must be plugged into an outlet that is properly installed and grounded.
DANGER - Improper use of the grounding plug can result in a risk of electric shock.
If repair or replacement of the cord or plug is necessary, do not connect the grounding wire
to either flat-head terminal.
Check with a qualified electrician or serviceman if the grounding wire instructions are not
completely understood, or if in doubt as to whether the product is properly grounded.
This product is factory equipped with a specific electric cord and plug to permit connection
to a proper electric circuit. Make sure that the product is connected to an outlet having the
same configuration as the plug.
No adapter should be used with this product. Do not modify the plug provided - if it will not fit
in the outlet, have the proper outlet installed by a qualified electrician.
If the product must be reconnected for use on a different type of electric circuit, the
reconnection should be made by qualified service personnel.
If it is necessary to use an extension cord, use only a three wire extension cord that has a
three blade grounding plug, and a three-slot receptacle outlet that will accept the plug on the
product.
Replace or repair a damaged cord.
SAVE THESE INSTRUCTIONS
10
(Continued)
Grounding pin

Operational Precautions

■ For prevention of malfunctions
● Do not block the body sensor or the remote control
transmitter or receiver.
< About the body sensors >
Two types of body sensors are used.
● Body sensor A detects changes in heat.
Detection may be difficult when the room temperature
• •
exceeds 86 °F (30 °C), such as in the summertime.
• • When sunlight is directly on the sensor area or a heater is
used in the bathroom, the sensor may detect incorrectly
due to the heat, resulting in the automatic operation of
functions such as auto lid opening and closing.
• • When the bathroom door is open, the sensor may detect
people who pass to the front or side of the toilet.
● Body sensor B detects when someone stands in
front of the toilet bowl.
Body sensor B emits an infrared beam as shown in the
• •
figure. When someone moves into the line of this infrared
beam, the sensor detects the person.
* Detection by the sensor may be difficult when the toilet
is used by someone small, such as a child.
Body sensor A Body sensor B
About the built-in seat sensor
When you sit on the toilet seat, the seat sensor turns ON,
enabling you to use various features.
(The deodorizer starts when the
<Detection range>
seat sensor makes a detection.)
Sit so your skin is in direct
contact with the seat sensor.
The seat sensor may not
detect properly if there is a
seat cover or clothing.
1-2/3"
Water droplets collecting on
(4 cm)
the seat sensor may cause
3-1/8"
(8 cm)
the main unit to malfunction. 4-3/4"
(12 cm)
Be sure to wipe off any water
droplets on the sensor.
■ For prevention of damage
● Wipe plastic areas
such as the main unit
and remote control
with a soft cloth tightly
Dry cloth or tissue
wrung out with water.
● Do not lean against
the toilet lid.
■ For prevention of malfunctions and failures
● Flip the power switch to OFF if there is a risk of
lightning.
● A toilet seat cover or a toilet lid cover cannot be used.
(The seat sensors may not function properly.
Additionally, the toilet seat and lid may not open or
close properly.)
Covers
● Do not urinate on the main unit, toilet seat or wand.
(Doing so may cause a failure or discoloration.)
● Do not apply strong forces to the control panel of the
remote control.
● When using a toilet cleaner to clean the toilet, rinse it
off within 3 minutes and leave the toilet seat and toilet
lid open.
(If vapor from a toilet cleaner enters the main unit, it
may cause a malfunction.)
Wipe off any cleaner that remains on the bowl unit.
• •
● Do not use the product with the toilet lid removed.
● Do not expose to direct sunlight.
(Doing so may cause changes in color, irregular
heated seat temperature, remote control malfunction
or the product malfunction due to the change in
temperature.)
● Use radios, etc. away from the product.
(The product could cause interference with the radio
signal.)
● If you use a booster seat for infants or a soft highchair,
remove it after use.
(Keeping it installed may prevent some of the
functions from being used.)
● Do not apply force to the remote control.
(May cause malfunction.)
To prevent the remote control from being dropped,
• •
set it in the hanger when you are not using it. Be
careful not to expose it to water.
● Do not place anything on top of the toilet seat.
Additionally, do not press it by hand.
(Doing so may activate the seat sensor, causing the
floor to get wet if buttons on the remote control are
touched and warm water comes out from the wand.)
11