Advertisement
Quick Links
Advertisement
Related Manuals for NCR 7409 K303
Summary of Contents for NCR 7409 K303
- Page 1 7409‐K303 Bar Code Scanner Replacement Kit Instructions Issue A ...
-
Page 2: Revision Record
Revision Record Issue Date Remarks A Apr 2011 First issue ... - Page 3 Introduction Use these instructions to replace the 7409‐K300/K305 Bar Code Scanner mounting brackets with the 7409‐K302 brackets. 7409-K303 7409-K300 7409-K305 ...
-
Page 4: Kit Contents
Kit Contents Nut, 6-32, KEPS Screw, 6-32 x 0.375, Phillips, Pan 006-8611426 006-8613117 Fixed Angle Mount Scanner Faceplate Fixed Angle Mount Scanner Mount 497-0472462 497-0472477 Screw, M3xPo.5 x 6 mm, Phillips, Flat Hd 006-8612557 Class 2 Laser Warning Label 497-0460286 Fixed Angle Mount Cable Cover 497-0467789 MS3207 Scanner Cable, DB9 to USB, 1 m... -
Page 5: Installation Procedures
Installation Procedures 1. Unplug the terminal’s power cord and turn off the power to any connected peripheral devices. 2. Remove the current scanner assembly (7409‐K300 or 7409‐K305). Removing 7409-K300 3. Open the unit to the service position. a. Remove the screws (2) in the sides of the Fixed Angle Mount. Screw (One On Each Side) ... - Page 6 b. Tilt the display as shown and rest the display on the Display Support. Display Support 29544 Note: Place the Display Support behind the extension on then Display Hinge Bracket. Bracket Extension Display Support 24753 ...
- Page 7 4. Remove the screws (3) that secure the Scanner Bracket to the terminal cabinet. Remove the assembly and disconnect the Scanner Cable from the terminal. 7409-K300 Bar Code Scanner Display Support 29543 5. Disconnect the Scanner Cable from the scanner. Discard this cable. 6. Remove the Bar Code Scanner from the Scanner Mounting Bracket (3 screws). Discard the bracket but retain the screws. 29541...
- Page 8 Removing 7409-K305 1. Open the unit to the service position. a. Remove the screws (2) in the sides of the Fixed Angle Mount. Screw (One On Each Side) ...
- Page 9 b. Tilt the display as shown and rest the display on the Display Support. Note: Place the Display Support behind the extension on then Display Hinge Bracket. Bracket Extension Display Support 24753 ...
- Page 10 2. Remove the screws (2) that secure the Scanner Bracket to the terminal cabinet. Remove the assembly and disconnect the Scanner Cable from the terminal. 3. Disconnect the Scanner Cable from the scanner. Discard this cable. 4. Remove the Bar Code Scanner from the Scanner Mounting Bracket (3 screws). Discard the bracket but retain the screws. ...
- Page 11 Assembling the new bracket assembly 1. Assemble the Scanner Faceplate and Scanner Mounting Bracket (2 hex nuts). Scanner Faceplate Scanner Mounting Bracket 29538 2. Install the Bar Code Scanner on the Scanner Mounting Bracket (3 screws). Bar Code Scanner 29539 3. Connect the new 1 meter Scanner Cable to the scanner. 29540...
- Page 12 4. 7409‐K300 Only: Remove the Blank Faceplate. a. Remove the screws (2) that secure the Blank Faceplate. b. Pivot the top of the Blank Faceplate out at the top as shown to remove it from the Fixed Angle Mount. 7409-K036 Blank Faceplate 29545 ...
- Page 13 5. Hook the bottom of the new Scanner Faceplate onto the bottom edge of the opening on the Fixed Angle Mount and then secure the assembly with screws (2). 29546 6. Route the Scanner Cable through the Bracket Cable Guides on the back of the terminal and then connect it to a USB connector on the I/O Panel. 29547 ...
- Page 14 7. Install the Cable Cover on the terminal (use the same three screw holes that were used to mount the previous scanner assembly. Cable Cover 29522 8. Adhere the Safety Label on the Scanner Mounting Bracket as shown. Safety Label 29548 9. Close the Display and secure it with screws (2). ...