Advertisement
Quick Links
Advertisement
Related Manuals for NCR 7407-K013
Summary of Contents for NCR 7407-K013
- Page 1 7407‐K013 Signature Capture Kit Instructions Issue A ...
-
Page 2: Revision Record
Revision Record Issue Date Remarks A Feb 2008 First issue ... - Page 3 7407-K013 Introduction This kit adds a Signature Capture device to the 7407. Signature Capture Module 25419 Caution: Static Electricity Discharge may permanently damage your system. Discharge any static electricity build up in your body by touching your computer’s case for a few seconds. Avoid any contact with internal parts and handle cards only by their external edges. ...
-
Page 4: Installation Procedure
7407-K013 Installation Procedure 1. Turn Off the power to the system and any connected peripheral devices. Unplug the system power cord. 2. Remove the Column Cover (2 screws). Column Cover 24895b ... - Page 5 7407-K013 3. Using a 7/16” nut driver, remove the hex bolts (4) that secure the Display Module to the countertop. 25017 ...
- Page 6 7407-K013 4. Remove the Mounting Plate from the countertop (2 screws). Note: Hold the Bolt Plate (underneath the countertop) while removing the screws to keep it from falling. Top of Countertop 10-32 x 2 Screws Mounting Plate Front of Cabinet 24920 Bottom of Countertop Front of Cabinet Bolt Plate 10-32 x 2 Screws 25422 ...
- Page 7 7407-K013 5. Unpack the Signature Capture kit. 6. Route the Signature Capture USB Cable down through the hole in the countertop. Front of Cabinet USB Cable 25420...
- Page 8 7407-K013 7. Insert the supplied 10‐32 x 2 in. hex bolts (2) through the inner holes in the Mounting Plate, Signature Capture Base, and countertop. Note: If the supplied screws are not long enough then obtain new 10‐32 screws that meet your requirements. 10-32 x 2 Screws Mounting Plate 25423...
- Page 9 7407-K013 8. Place the Bolt Plate (removed earlier in Step #2) under the countertop and thread the screws through it. Secure the Mounting Plate to the predrilled holes in the countertop, using the appropriate type screws for the two inner holes. Note: Pre‐installation cabinet and countertop preparation is discussed in the NCR 7407 XpressPort Hotel Check‐In Site Preparation Guide (B005‐0000‐1803). Bottom of Countertop Front of Cabinet Bolt Plate 10-32 x 2 Screws 25422 ...
- Page 10 7407-K013 9. Remove the foam packing from the Display Module and then install the module onto the Mounting Plate Display Module Column 25421 ...
- Page 11 7407-K013 10. Insert the supplied hex bolts (4) through the Column, the Mounting Plate, countertop, and screw them into the Bolt Plate. 25424 Note: If the supplied bolts are not the correct length for your particular countertop, obtain four ¼“ Hex‐head bolts of sufficient length, as long as needed but not so long that they may interfere with the cable routing underneath the countertop. 11. Tighten the bolts evenly using a 7/16” nut driver. ...
- Page 12 7407-K013 12. Bundle the cables inside the Display Column using the supplied Velcro Tie or a Tie Wrap. Velcro 25034a ...
- Page 13 7407-K013 13. Install the Column Cover. Slide the upper tab into the slot and secure it with screws (2) in the bottom. Column Cover 24895a ...
- Page 14 7407-K013 14. Snap the Signature Capture USB Cable into the Cable Guide. Cable Guide USB Connector 25425 15. Route the coiled cable beside the printer and connect it to a USB port on the Output Module. ...