Power Source; Basic Setup; Starting Setup - Toshiba 15DLV77B Service Manual

Connections
Connecting to optional equipment (Continued)
Connecting to an optional equipment with S-video output
If you connect a VCR with an S-VIDEO cable to the S-VIDEO IN jack on the left side of the TV/DVD, you must
also connect the audio cables to the AUDIO IN (LINE 1 IN) jacks on the left side of the TV/DVD. The S-VIDEO
cable only carries the video signal. The audio signal is separated.
Select the "VIDEO1" by pressing INPUT repeatedly.
: Signal fl ow
Ex. VCR with S-Video
To AUDIO (L/R) IN
(playback)
To Audio (L/R) OUT
To S-VIDEO OUT
Audio cable (not supplied)
S-Video cable (not supplied)
Note: When the S-VIDEO cable and the standard video cable are connected at the same time, the S-video cable takes precedence.
Connecting an optional equipment with ColorStream
Your TV/DVD is capable of using ColorStream ® (component video). Connecting your TV/DVD to a component
video compatible DVD player, such as a Toshiba DVD player with ColorStream
quality and performance.
Select the "ColorStream HD" by pressing INPUT repeatedly.
Ex. DVD player with Component video
: Signal fl ow
To Component To Audio (L/R) OUT
Video OUT
Audio cable (not supplied)
Component video cable (not supplied)
When using the Component video cable,
an Audio cable must be connected to
AUDIO IN (L/R) (LINE 2 IN) jacks.
Notes:
• The ColorStream ® inputs on this unit are for use with devices that output 480i, 1080i interlaced signals and
480p, 720p progressive signals.
• Refer to the owner's manual of the connected equipment as well.
• When you connect the unit to other equipment, be sure to turn off the power and unplug all of the equipment
from the wall outlet before making any connections.
• If you place the unit near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the
unit away from the tuner and radio.
16
Connections Connections
Connecting to optional equipment (Continued)/Power source
Connecting to an amplifi er equipped with an MPEG audio decoder
MPEG2 sound
You can enjoy motion picture and live concert DVD video discs encoded via the MPEG2 recording system with dynamic
realistic sound by connecting an amplifi er equipped with an MPEG2 audio decoder or MPEG2 audio processor.
Amplifi er equipped with an
MPEG2 audio decoder
To COAXIAL DIGITAL
AUDIO OUT
To COAXIAL
type digital
audio input
75 coaxial cable (not supplied)
Connecting to an amplifi er equipped with a digital audio input
2 channel digital stereo
You can enjoy the dynamic sound of 2 channel digital stereo by connecting an amplifi er equipped with a digital audio input and
speaker system (right and left front speakers).
Note: PCM audio is limited to DVD or CD playback.
Amplifi er equipped with a
Digital audio input
To COAXIAL DIGITAL
AUDIO OUT
To COAXIAL
type digital
audio input
75 coaxial cable (not supplied)
Notes:
• DO NOT connect the COAXIAL DIGITAL AUDIO OUT jack of the TV/DVD to the AC-3 RF input of a Dolby Digital Receiver.
This input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the COAXIAL DIGITAL AUDIO
OUT jack of the TV/DVD.
• Connect the COAXIAL DIGITAL AUDIO OUT jack of the TV/DVD to the "COAXIAL" input of a Receiver or Processor.
• Refer to the owner's manual of the connected equipment as well.
• When you connect the TV/DVD to other equipment, be sure to turn off the power and unplug all of the equipment from the
wall outlet before making any connections.
• The output sound of the TV/DVD has a wide dynamic range. Be sure to adjust the receiver's volume to a moderate listening level.
Otherwise, the speakers and your hearing may be damaged by a sudden high volume sound.
• Turn off the amplifi er before you connect or disconnect the TV/DVD's power cord. If you leave the amplifi er's power on, the
speakers may be damaged.

Power source

AC Outlet TO USE AC POWER SOURCE
Wider Hole
Use the AC polarized line cord provided for operation on AC. Insert the AC cord plug
and Blade
into a standard 120V 60Hz polarized AC outlet.
Notes:
• Never connect the AC line cord plug to other than the specifi ed voltage (120V 60Hz).
Use the attached power cord only.
• If the polarized AC cord does not fi t into a non-polarized AC outlet, do not attempt to
fi le or cut the blade. It is the user's responsibility to have an electrician replace the
obsolete outlet.
Polarized AC Cord Plug
• If you cause a static discharge when touching the unit and the unit fails to function, simply unplug
(One blade is wider than the other.)
the unit from the AC outlet and plug it back in. The unit should return to normal operation.
• If the AC cord plug is plugged in for the fi rst time, wait for approx. 5 seconds before
pressing the POWER button.
18
Left side (LINE 1 IN)
(white)
(red)
To S-VIDEO IN
®
(Component video) output
®
can greatly enhance picture
Rear lower right of the TV
To AUDIO (L/R) IN
To ColorStream HD
(Y, P P ) IN
B, R
* This section uses the following reference mark.
: Front speaker : Center speaker
: Rear speaker : Signal fl ow
: Sub woofer
Left side (LINE 1 IN)
Left side (LINE 1 IN)
You can enjoy high quality dynamic sounds by connecting the
TV/DVD to optional audio equipment.
Connecting to an amplifi er equipped with a Dolby
Dolby Digital
Dolby Digital is the surround sound technology used in theaters showing the latest movies, and is now available to reproduce
this realistic effect in the home. You can enjoy motion picture and live concert DVD video discs encoded via the Dolby Digital
recording system with this dynamic realistic sound by connecting the TV/DVD to a 6 channel amplifi er equipped with a Dolby
Digital decoder or Dolby Digital processor. If you have a Dolby Surround Pro Logic decoder, you will obtain the full benefi t of
Pro Logic from the same DVD movies that provide full 5.1-channel Dolby Digital soundtracks, as well as from titles with the
Dolby Surround mark.
Amplifi er equipped with a
Dolby Digital decoder
To COAXIAL
type digital
audio input
75 coaxial cable (not supplied)
Connecting to an amplifi er equipped with a DTS
Digital Theater Systems (DTS)
DTS is a high quality surround technology used in theaters and now available for home use, on DVD video discs or audio CDs.
If you have a DTS decoder or processor, you can obtain the full benefi t of 5.1 channel DTS encoded sound tracks on DVD
video discs or audio CDs.
Amplifi er equipped with
a DTS decoder
To COAXIAL
type digital
audio input
75 coaxial cable (not supplied)

Basic setup

Starting setup

The STARTING SETUP function helps to install your unit easily.
It leads you the Language selection, TV/CABLE selection and auto
channel memory automatically.
IMPORTANT: Make sure that the antenna or cable TV system
connection is made!
Starting setup
1
To turn on the TV/DVD, press POWER.
The Power indicator on the front of the main unit
will light.
2
The starting setup function begins and the
Language setup menu appears on the screen.
Press or to select your desired language,
then press ENTER.
3
Press or to select "TV" or "CABLE", then
press ENTER.
4 Press or to select "START", then press
ENTER.
If you select "CANCEL" and press
ENTER, the STARTING SETUP
stops and changes to the TV screen.
* This section uses the following reference mark.
: Front speaker : Center speaker
: Rear speaker : Signal fl ow
: Sub woofer
® Digital decoder
Left side (LINE 1 IN)
To COAXIAL DIGITAL
AUDIO OUT
Manufactured under license
from Dolby Laboratories.
Dolby and the double-D symbol
are trademarks of Dolby
Laboratories.
® decoder
Left side (LINE 1 IN)
To COAXIAL DIGITAL
AUDIO OUT
"DTS" and "DTS Digital Out"
are registered trademarks of
DTS, Inc.
17
POWER
/
ENTER
EXIT/CANCEL
5
Now the "CH PROGRAM" starts.
After the starting setup is completed,
the TV channel appears on the screen.
Notes:
• The starting setup function will work only when you
press POWER for the fi rst time.
• The process of "CH PROGRAM" may take 15 to 30
minutes to complete, depending on your regional cable
service.
• If you press EXIT/CANCEL in the process of "CH
PROGRAM", starting setup function is canceled.
19