Power Source; Basic Setup; Setting The Language; To Memorize Channels - Toshiba 15DLV77C Service Manual

Connections Connections

Power source

Power connection
To DC input jack
TO USE AC POWER
1. Connect the AC cord to the AC adapter.
2. Connect the AC adapter plug into the TV/DVD's DC input jack.
3. Connect the AC cord into a wall outlet.
Notes:
• Make sure to insert the plug of each cord securely.
• During use the AC adapter becomes warm. This is not a malfunction.
WARNING:
• DO NOT CONNECT THIS UNIT TO THE POWER USING ANY DEVICE OTHER THAN THE SUPPLIED AC ADAPTER OR
POWER CORD. THIS COULD CAUSE FIRE, ELECTRIC SHOCK, OR DAMAGE.
• DO NOT USE WITH A VOLTAGE OTHER THAN THE POWER VOLTAGE DISPLAYED. THIS COULD CAUSE FIRE,
ELECTRIC SHOCK, OR DAMAGE.
CAUTION:
• DO NOT USE THE AC ADAPTER IF IT IS COVERED BY A CLOTH ETC., OR PRESSED INTO A NARROW AREA.
THIS RESULTS IN POOR DISSIPATION OF HEAT AND MAY CAUSE FIRE, ELECTRIC SHOCK, OR DAMAGE.
• WHEN THIS UNIT IS NOT USED FOR AN EXTENDED PERIOD OF TIME, (E.G., AWAY ON A TRIP) IN THE INTEREST OF
SAFETY, BE SURE TO UNPLUG IT FROM THE WALL OUTLET.
• DO NOT PLUG/UNPLUG THE PLUG WHEN YOUR HANDS ARE WET. THIS MAY CAUSE ELECTRIC SHOCK.
• IF YOU NEED TO REPLACE THE SUPPLIED AC ADAPTER OR AC CORD, THE SPECIFIED AC ADAPTER AND AC
CORD MUST BE USED. CONTACT THE DEALER THAT YOU PURCHASED THE UNIT FROM.
20
J5X00401A(Eng).indb 20

Basic setup

To memorize channels

This TV/DVD is equipped with a channel memory feature which allows
channels to skip up or down to the next channel set into memory, skipping over
unwanted channels. Before selecting channels, they must be programmed
into the TV/DVD's memory. In addition to normal VHF and UHF channels, this
TV/DVD can receive up to 113 Cable TV channels. To use this TV/DVD with an
antenna, set the TV/CABLE selection to the TV position. When shipped from
the factory, this selection is in the CABLE position.
TV/CABLE selection
1
Press MENU in the TV mode, then press
to select SETUP.
P I C T U R E A U D I O S E T U P
S E T U P
L A N G U A G E E N G L I S H
T V / C A B L E C A B L E
C H P R O G R A M
A D D / E R A S E A D D
C L O S E D C A P T I O N O F F
: S E L E C T : A D J U S T
2
Press or to select "TV/CABLE".
P I C T U R E A U D I O S E T U P
S E T U P
L A N G U A G E E N G L I S H
T V / C A B L E T V / C A B L E
C H P R O G R A M
A D D / E R A S E A D D
C L O S E D C A P T I O N O F F
: S E L E C T : A D J U S T
3
Press or to select "TV" or "CABLE".
TV - VHF/UHF channels
CABLE - Cable TV channels
P I C T U R E A U D I O S E T U P
S E T U P
L A N G U A G E E N G L I S H
T V / C A B L E T V / C A B L E
C H P R O G R A M
A D D / E R A S E A D D
C L O S E D C A P T I O N O F F
: S E L E C T : A D J U S T
4
Press CANCEL to clear the menu screen.
CANCEL
Cable TV chart
The chart below is typical of many cable system channel
allocations.
22
J5X00401A(Eng).indb 22
AC 120V,
60Hz
2
3
1
AC adapter
AC cord
(supplied)
(supplied)
3/5/2550 12:11:13
0–9
CANCEL
/ / /
CH +/–
MENU
Automatic memory tuning
or
Press MENU, then press or to select SETUP.
Press or to select the "CH PROGRAM", then
press .
The TV will begin memorizing all the channels
available in your area.
P I C T U R E A U D I O S E T U P
S E T U P
L A N G U A G E E N G L I S H
T V / C A B L E C A B L E
C H P R O G R A M
A D D / E R A S E A D D
C L O S E D C A P T I O N O F F
: S E L E C T : A D J U S T
To ADD/ERASE channels
1
Select the desired channel to be added or
deleted using Direct channel selection (0–9) or
CH +/–.
2
Press MENU, then press or to select
SETUP. Press or to select "ADD/ERASE".
P I C T U R E A U D I O S E T U P
S E T U P
L A N G U A G E E N G L I S H
T V / C A B L E C A B L E
C H P R O G R A M
A D D / E R A S E A D D / E R A S E
C L O S E D C A P T I O N O F F
: S E L E C T : A D J U S T
3
Press or to select "ADD" or "ERASE".
4
Press CANCEL to clear the menu screen.
Repeat steps 1 ~ 3 to add or erase other channel.
CANCEL
3/5/2550 12:11:15
Basic setup

Setting the language

This TV/DVD can display the on screen language in English, Spanish or French in
the TV mode.
Select the language you prefer À rst, then proceed with the other menu options.
Setting the language
1
To turn on the TV/DVD, press POWER.
The Power indicator on the front of the main unit
will light.
2
Press MENU and then press or to select
"SETUP".
P I C T U R E A U D I O S E T U P
S E T U P
L A N G U A G E E N G L I S H
T V / C A B L E C A B L E
C H P R O G R A M
A D D / E R A S E A D D
C L O S E D C A P T I O N O F F
: S E L E C T : A D J U S T
3
Press or to select "LANGUAGE", then
press or to select the desired language:
English (ENGLISH), Spanish (ESPAÑOL) or
French (FRANÇAIS), then press ENTER.
P I C T U R E A U D I O S E T U P
S E T U P
L A N G U A G E E N G L I S H
E N G L I S H / F R A N Ç A I S / E S PA Ñ O L
T V / C A B L E C A B L E
C H P R O G R A M
A D D / E R A S E A D D
C L O S E D C A P T I O N O F F
: S E L E C T : A D J U S T
4
Press CANCEL to clear the menu screen.
CANCEL
Notes:
• If the unit does not operate properly, or No key operation
(by the unit and/or the remote control): Static electricity,
etc., may affect the TV/DVD's operation. In such case,
disconnect the AC cord once, then connect it again.
• The TV section has its own menu and also DVD section has
its own menu .
44
J5X00401A(Eng).indb 21

TV operation

TV operation
TV operation
1 To turn on the TV/DVD, press POWER.
The Power indicator on the front of the main unit
will light.
2
Adjust the volume level by pressing VOL + or
–. The volume level will be indicated on the
screen by white bars. As the volume level
increases, so do the number of bars. If the
volume decreases, the number of white bars
also decreases.
VOLUME 32
3
Set the TV/CABLE selection to the appropriate
position.
22
TV - VHF/UHF channels
CABLE - Cable TV channels
Auto power off
If a station being viewed stops broadcasting, the TV will
automatically shut itself off after 15 minutes.
J5X00401A(Eng).indb 23
POWER
CANCEL
ENTER
/ / /
MENU
21
3/5/2550 12:11:13
POWER
0–9
VOL +/–
4
Press direct channel selection (0–9) to select
the channel.
TV mode direct channel selection
When the TV/CABLE selection is in the TV
position, all channels can be instantly selected by
using two buttons. (for example, to select channel
2, press "0", then "2".
If you press only "2",
channel selection
will be delayed for
a few seconds.) For
channels 10 and
above, press the 2
ANT
02
digits in order.
CABLE mode direct channel selection
When the TV/CABLE selection is in the CABLE
position, channels can be selected as follows:
TO SELECT CABLE TV CHANNELS:
1-9: Press "0" twice, then 1-9 as needed.
Example, to select channel 2, press
"002".
10-12: Press "0", then the remaining 2 digits.
Example, to select channel 12, press
"012".
13-99: Press the 2 digits in order. Example, to
select channel 36, press "36".
100-125: Press the 3 digits in order. Example, to
select channel 120, press "120".
NOTE FOR CHANNELS 1-12:
If only 1 or 2 buttons are pressed, the corresponding
channel will be selected in 2 seconds.
CATV
TV
VHF VHF
2-13
2-13
UHF STD/HRC/IRC
14-36
14-69
(A) (W)
37-59
(AA) (WW)
60-85
(AAA) (ZZZ)
86-94
(86) (94)
95-99
(A-5) (A-1)
100-125
(100) (125)
01
(5A)
Note:
If a channel with no broadcast is selected, the sound will
automatically be muted.
23
3/5/2550 12:11:17