Page 2
Hazardous Substances. From July 1, 2006, the RoHS Directive will prohibit any marketing of new products containing the restricted substances. Increasing attention is given to issues related to the global environmental. Toshiba Corporation recognizes environmental protection as a key management tasks, and is doing its utmost to enhance and improve the quality and scope of its environmental activities.
Page 6
FILE NO. 810-200688GR SERVICE MANUAL 15-inch Diagonal LCD TV/DVD COMBINATION 15DLV77 The above model is classified as a green product (*1), as indicated by the underlined serial number. This Service Manual describes replacement parts for the green product. When repairing this green product, use the part(s) described in this manual and lead-free solder (*2).
Page 7
Hazardous Substances. From July 1, 2006, the RoHS Directive will prohibit any marketing of new products containing the restricted substances. Increasing attention is given to issues related to the global environmental. Toshiba Corporation recognizes environmental protection as a key management tasks, and is doing its utmost to enhance and improve the quality and scope of its environmental activities.
DVD and CD Software and/or the manufacture Video CD/Audio CD of DVD and CD discs, Toshiba cannot assure that the • Video CD not equipped with PBC function (Version 1.1) DVD player contained in this TV will successfully play...
Introduction Connections Antenna connections Identifi cation of controls (Continued) If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your antenna system. If you are using a cable TV service (CABLE), see page 14 for Cable TV connections. Combination VHF/UHF antenna (Single 75 ohm cable or 300 ohm twin-lead wire) Inserting batteries Install two “R03/AAA”...
DTS is a high quality surround technology used in theaters and now available for home use, on DVD video discs or audio CDs. ® video compatible DVD player, such as a Toshiba DVD player with ColorStream can greatly enhance picture If you have a DTS decoder or processor, you can obtain the full benefi...
Basic setup To memorize channels Setting the language This TV/DVD can display the on screen language in English, Spanish or French This TV/DVD is equipped with a channel memory feature which allows in the TV mode. channels to skip up or down to the next channel set into memory, skipping Select the language you prefer fi...
TV operation Programming your favorite channels Setting the closed captions (analog caption/ TV/DVD 0–9, 100/- You can preset up to 12 of your favorite channels using the Favorite digital caption) Channel Programming feature. Because this feature scans through only your favorite channels, it allows you to skip other channels you WHAT IS CLOSED CAPTIONING? do not normally watch.
TV operation Setting the V-Chip (Continued) As a supplement to the standard V-Chip rating system, your Toshiba Television will be able to download an additional rating system, if such a system becomes DISPLAY available in the future. MUTE ENTER / / /...
TV operation Selecting the cinema mode Picture control adjustment/ When you view a DVD movie (3:2 pulldown processed) smoother Adjusting the picture mode and more natural motion can be obtained by setting the CINEMA MODE to FILM. Picture controls are factory preset but you can adjust them individually as follows: If you view a DVD movie from a DVD player connected to the And also you can select four picture modes—...
Selecting the audio languages/ Checking the signal meter/ Selecting the digital output Using the auto shut off feature / / / EXIT/CANCEL / / / MENU EXIT/CANCEL MENU To select the audio languages To select the digital output To check the signal meter To use the auto shut off feature signal, you can select one of the audio language.
Basic playback Advanced playback Zooming/Locating desired scene Playing a disc (Continued) 0–9 PAUSE JUMP PLAY DISPLAY SKIP ZOOM / FF / / / SLOW ENTER EXIT/CANCEL Zooming Locating desired scene Playing in fast reverse or fast forward directions This unit will allow you to zoom in on the frame image. Use the title, chapter and time recorded on the DVD disc to To resume normal playback Press REV or FF during playback.
Advanced playback Changing angles/Title selection/DVD menu Program playback/Random playback 0–9 You can arrange the playback order of tracks on the disc. And the DVD MENU unit can also select tracks at random and playback them. These features work for Video CD. / / / PLAY MODE ENTER...
MP3/WMA CD playback You must obtain any required permission from copyright owners to download or use copyrighted content. Toshiba cannot and does not grant such permission. Load a disc on which MP3 or WMA fi les have About fi le menu Audio CD/MP3/WMA/JPEG/DivX ®...
Advanced playback Repeat, random and program playback using fi le browser / / / / / / ENTER ENTER PLAY SKIP PLAY Repeat playback (CD) Random playback (CD) Program playback (CD) In the fi le browser, press to select Press to select “Program View”, then In the fi...
Page 22
Function setup Customizing the function settings (Continued) Setting details Setting details Picture Mode JPEG Interval Parental E.B.L. Menu : Off : Off : Off : English Parental Menu TV Screen : Off : Off : English : 4:3 QSound TV Screen Subtitle Set Password : On...
Function setup Others EJECT Temporary cancel the rating level by DVD disc Language code list 0–9 Enter the appropriate code number for the initial settings “Menu”, “Subtitle” and/or “Audio” Depending on the DVD disc, the disc may try to temporarily cancel the rating level that you have set.
LCD TV/DVD Combination - Depot Repair Warranty be commenced to enforce any obligation of TACP Toshiba America Consumer Products, L.L.C. (“TACP”) makes the following limited warranties to original arising under the warranty or under any statute (1) For instructions on how to obtain warranty consumers in the United States.
Page 25
CAUTION THIS LCD COLOR TELEVISION EMPLOYS A LASER SYSTEM. TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS SERVICE MANUAL CARE- FULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE, CONTACT AN AUTHORIZED SERVICE LOCATION-SEE SERVICE PROCEDURE. USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS LASER RADIATION EXPOSURE.
Page 26
IMPORTANT SERVICE SAFETY INFORMATION Safety precautions to be followed during servicing: Parts marked with an are critical parts for safety. Replace only with the one described in the parts list. Before returning the DVD product to the customer, make the appropriate leakage current check or resistance measurements to ensure that exposed parts are properly insulated from the supply circuit.
Page 27
IMPORTANT SAFEGUARDS 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Page 28
IMPORTANT SAFEGUARDS (CONTINUED) 19) If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for...
Page 29
IMPORTANT SAFEGUARDS (CONTINUED) 25) Do not allow the product to output distorted sound for an extended period of time. It may cause speaker overheating and fire. 26) When you use the headphones, keep the volume at a moderate level. If you use the headphones continu- ously with high volume sound, it may cause hearing damage.
Page 30
WHEN REPLACING DVD DECK [ When removing the DVD Deck ] Before removing Pick Up PCB and DVD PCB connector, the short circuit the position shown in Fig. 1 using a soldering iron. If you remove the DVD Deck with no soldering, the Laser may be damaged. [ When installing the DVD Deck ] Remove all the soldering on the short circuit position after the connection of Pick Up PCB and DVD PCB connector.
Page 31
DISC REMOVAL METHOD AT NO POWER SUPPLY Remove the Back Cabinet and Angle Deck. (Refer to item 1 of the DISASSEMBLY INSTRUCTIONS.) Slide the Belt Loading toward the arrow direction by hand to release the lock. (Refer to Fig. 1) Take out the Disc from the DVD Deck.
Page 32
TABLE OF CONTENTS ï GREEN PRODUCT PROCUREMENT ï LEAD-FREE SOLDER ï OWNER'S MANUAL A1-1 CAUTION ........................A1-2 IMPORTANT SERVICE SAFETY INFORMATION ............. A1-3~A1-5 IMPORTANT SAFEGUARDS ..................A1-6 WHEN REPLACING DVD DECK ................A1-7 DISC REMOVAL METHOD AT NO POWER SUPPLY ..........A1-7 PARENTAL CONTROL - RATING LEVEL ..............
Page 33
GENERAL SPECIFICATIONS LCD Size / Visual Size 15.0 inch / 380.0mmV System LCD Type Color TFT LCD Number of Pixels 1024(H) x 768(V) View Range Left/Right 70/70 degree Up/Down 65/60 degree Color System NTSC Speaker 2 Speaker Position Front Size 1.5 x 2.7 inch Impedance 8 ohm...
Page 34
Timer Back-up (at Power Off Mode) more than G-10 Remote Unit RC-LT Control Glow in Dark Remocon Remocon Format TOSHIBA Format TOSHIBA Custom Code 40-BF h ,44-BB h ,45-BA h ,45-BC h Power Source Voltage(D.C) UM size x pcs UM-4 x 2 pcs...
Page 35
GENERAL SPECIFICATIONS G-11 Features Auto Shut Off (TV) Auto Search Power On Memory Comb Filter Game Position Auto Setup(Language/CH Program) Picture Setting Mode(Picture Preference) Brightness , Contrast , Color Tint Sharpness Color Temperature Cable Clear Audio Tone Control (Bass/Treble/Balance) Stable Sound Surround SRS WOW (SRS 3D/Focus/Tru Bass) Valiable Audio Out...
GENERAL SPECIFICATIONS Features Tray Lock (DVD) JPEG Video CD Playback SVCD Playback Overlay Graphics And Text Command List Entry Point Jump MP3 Playback Divx Playback DMF Support Digital Out (Dolby Digital) (MPEG) (PCM) (DTS) Down Mix Out (Dolby Digital) (DTS) 3D Surround Closed Caption Screen Saver...
Page 37
Container Stuffing (40' container) Sets/40' container G-17 Material Cabinet Front PS 94V0 DECABROM Rear PS 94V0 DECABROM Jack Panel Non-Halogen Demand Eyelet Demand G-18 Environment Environmental standard requirement (by buyer) Green procurement of TOSHIBA Pb-free Phase3 (Phase3A) Measures for Whisker A3-5...
DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF MECHANICAL PARTS 1-3: ANGLE BACK (Refer to Fig. 1-3) AND P.C. BOARDS Remove the 3 screws (1). Remove the Angle Back in the direction of arrow. 1-1: HINGE ASS'Y (Refer to Fig. 1-1) Remove the 3 screws (1). Remove the Stand in the direction of arrow (A).
Page 39
DISASSEMBLY INSTRUCTIONS 1-5: ANGLE DVD ASS'Y (Refer to Fig. 1-5) 1-5: ANGLE DVD ASS'Y (Refer to Fig. 1-5) 1-5: ANGLE DVD ASS'Y (Refer to Fig. 1-5) 1-5: ANGLE DVD ASS'Y (Refer to Fig. 1-5) 1-5: ANGLE DVD ASS'Y (Refer to Fig. 1-5) NOTE Before your operation, please read "PREPARATION OF Disconnect the following connectors:...
Page 40
DISASSEMBLY INSTRUCTIONS 1-8: DIGITAL PCB (Refer to Fig. 1-8) 1-10: BACK LIGHT PCB (Refer to Fig. 1-10) Disconnect the following connectors: Disconnect the following connectors: (CP7001, CP7002, CP7003 and CP7004). (CP106, CP507 and CP2407). Remove the 7 screws 1. Remove the 4 screws 1. Remove the Shield Digital and Digital PCB in the direction Remove the Shield Inverter and Back Light PCB in the of arrow.
Page 41
DISASSEMBLY INSTRUCTIONS 1-11: REMOCON PCB/COVER LCD/LCD PANEL (Refer to Fig. 1-11) Remove the 2 screws 1. Remove the Remocon PCB in the direction of arrow (A). Remove the 2 screws 2. Remove the Angle Hinge in the direction of arrow (B). Remove the 3 screws 3.
DISASSEMBLY INSTRUCTIONS 2. REMOVAL OF DVD DECK PARTS Check Hook NOTE Check Hook Check Hook 1. Disassemble only the DVD DECK PARTS parts listed here. Minute adjustments are needed if the disassembly is done. If the repair is needed except listed parts, replace the DVD MECHA ASS'Y.
Page 43
DISASSEMBLY INSTRUCTIONS NOTE Traverse Ass'y When installing the Rack Feed Ass'y, push both ends to Check Hook align the teeth as shown Fig. 2-2-B. Then install it. In case of the Gear Motor installation, check if the value Check Hook of the Fig.
DISASSEMBLY INSTRUCTIONS 3. REMOVAL AND INSTALLATION OF FLAT 3. When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using PACKAGE IC a tweezers and remove the IC by moving with the IC REMOVAL desoldering machine.
Page 45
DISASSEMBLY INSTRUCTIONS INSTALLATION 4. When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thin- 1. Take care of the polarity of new IC and then install the tip Soldering Iron. (Refer to Fig. 3-8.) new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily.
SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter to the SERVICE MODE function, press and hold both buttons simultaneously on the main unit and on the remote control for more than a the standard time in the appropriate condition.
SERVICING FIXTURES AND TOOLS Ref. No. Remarks Part No. Parts Name JG176 Up-Date Disc JG176 APJG176117 Up-Date Disc Up-Date of the Firmware RE-WRITE FOR DVD FIRMWARE Turn on the power, and set the DVD mode. Confirm that the “No Disc” will be appeared on the screen. Press both VOL.
WHEN REPLACING EEPROM (MEMORY) IC CONFIRMATION OF CHECK SUM, POWER ON TOTAL HOURS AND MICON VERSION Initial total of MEMORY IC, POWER ON total hours and MICON VERSIONcan be checked on the screen. Total hours are displayed in 16 system of notation. NOTE: If you set a factory initialization, the total hours is reset to "0".
ELECTRICAL ADJUSTMENTS 1. ADJUSTMENT PROCEDURE FUNCTION FUNCTION Read and perform these adjustments when repairing the H POSI OSD BAK LIGHT CENT V POSI OSD BAK LIGHT MAX circuits or replacing electrical parts or PCB assemblies. R DRIVE(N) BAK LIGHT MIN CAUTION R CUT OFF(N) BRIGHT CENT...
Page 59
ELECTRICAL ADJUSTMENTS 2-2: WHITE BALANCE Place the set in Aging Test for more than 15 minutes. Receive the gray scale pattern from the Pattern Generator. Using the remote control, set the brightness and contrast to normal position. Activate the adjustment mode display of Fig. 1-1 and press the channel button (03) on the remote control to select "R DRIVE(N)".
Page 61
ELECTRICAL ADJUSTMENTS 3. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION) LCD PANEL DVD DECK DVD MT PCB CP2303 CD2301 CP2302 CD2001 CP2301 CP3001 CD8501 BACK LIGHT PCB OPERATION PCB CP2001 CP7003 CP7001 REMOCON PCB CD2004 CP7004 CP7002 CP701 CD3001 AC IN J702 J706 CD502...
TROUBLESHOOTING GUIDE (LCD SECTION) POWER DOES NOT TUNER ON Change F501. Is F501 broken? Check IC506 and peripheral Is there voltage at pin 7 circuit. of IC506 17.7V? Change F502. Is F502 broken? Is there voltage at Check Q507, IC501, IC503 pin 6 of Q507 5V? and peripheral circuit.
Page 63
TROUBLESHOOTING GUIDE THE PICTURE APPEARS, BUT THE AUDIO DOES NOT APPEARS. (ATRFMODE) Connect CP1001. Is CP1001 connected? Is there signal at pins Change SP1001. 1 and 4 of CP1001? Check IC1001 and peripheral Is there signal at pins circuit. 2 and 4 of IC1001? Is there signal at pins 1 Check IC1002 and peripheral and 20 of IC1002?
Page 64
TROUBLESHOOTING GUIDE THE PICTURE DOES NOT APPEAR (1) Check IC506, T501 and Is there voltage at pins 1, 2 Does backlight shine? peripheral circuit. and 3 of CP505 12V? Is CD7201 connected? Connected CD7201. Is there signal at pins 5, 6, 8, 9, 11, 12, 14, 15, 17 Change V2301.
Page 65
TROUBLESHOOTING GUIDE THE PICTURE DOES NOT APPEAR (2) Is there signal at pins Check IC701 and 33 and 35 of IC701? peripheral circuit. Is there signal at pins A9 Check IC2401 and and A13 of IC2401? peripheral circuit. Is there signal at Check IC2401 and C2528 and C2532? peripheral circuit.
Page 66
TROUBLESHOOTING GUIDE THE COLOR DOES NOT APPEAR Is setting of color Adjust the color. normal? Is the color signal Receive the color signal. received? Is there color signal at Check IC2401 and pins A9 and A13 of peripheral circuit. IC2401? Change DIGITAL PCB.
Page 67
TROUBLESHOOTING GUIDE ON SCREEN DISPLAY DOES NOT APPEAR Is there signal at pins Check IC2401 and AF11, AE10, AF9 and peripheral circuit. AD10 of IC2410? Check NR6603 and Is there signal at pins 68, peripheral circuit. 69, 70 and 71 of IC6601? Check IC6601 and peripheral circuit.
Page 68
TROUBLESHOOTING GUIDE (DVD SECTION) DOES NOT DISPLAY DVD PICTURE Does this display Check the disc. logo picture? Check pins 12 and 16 of Does this have signal at CP8501 and peripheral circuit. pins 151 and 153 of IC4001? Does IC4001 gets Change IC4001.
Page 69
TROUBLESHOOTING GUIDE DISC DOES NOT EJECT Check pins AD18 and AF19 Does OSD appear Is remote key set of IC2401 and peripheral on the screen? effectively? circuit. Check pins 205 and 206 of IC4001 and peripheral circuit. Does this eject disc at Does this have signal at Check IC2301 and change DVD DECK?
Page 70
TROUBLESHOOTING GUIDE DOES NOT PLAY DVD Change DVD DECK. Is the voltage between Does CD2001 connect Does this display JG017 and JG018 less with CP2301 correctly? "INCORRECT DISC"? than 0.6V? Connect CD2301. Does this display Change IC4001. reading mark? Change DVD DECK. Does disc rotate? Change IC4001.
Page 71
TROUBLESHOOTING GUIDE DOES NOT PLAY CD Change DVD DECK. Is the voltage between Does CD2001 connect Does this display JG019 and JG018 less with CP2301 correctly? "INCORRECT DISC"? than 0.6V? Connect CD2301. Does this display Change IC4001. reading mark? Change DVD DECK. Does disc rotate? Change IC4001.
Page 72
TROUBLESHOOTING GUIDE NO SOUND DVD/CD ANALOG AUDIO Does this have signal at pins 8 and 10 of Refer to "LCD SECTION". CP8501? Does this have signal Check pins 7 and 8 of IC8501 at pins 7 and 8 of and peripheral circuit. IC8502? Does this have signal at pins 113, 115, 116...
Page 75
DVD DECK EXPLODED VIEW CD2001 M2602 Do not replace the parts. Because, minute adjustments are needed if this condition is disassembled further more. If the repair is needed, replace the DVD MECHA ASS'Y. PCB640 (SW PCB ASS'Y) CD2301 Applying positions AA for the grease are displayed for this section. NOTE: CLASS MARK...
Page 76
MECHANICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description AE008935 7A7010256A FRONT CABI ASS'Y 101A AE008936 701WPB0215 CABINET FRONT 101B AE008937 711WND0040 PLATE DISPLAY 101C AE007694 7235490068 BADGE BRAND 101D AE008938 800WQ00121 FELT SHEET 6*250*T0.5 AE008939 7A7020116A BACK CABI ASS'Y 102A AE008940 702WPA1270 CABINET BACK...
Page 77
MECHANICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description AE007212 810213060U SCREW PAN M3*6 CH AE005675 810923060U SCREW TAP TITE(B) BIND 3*6 CH AE003528 8110630A0U SCREW TAP TITE(P) BRAZIER 3*10 CH AE008988 8110630A2S SCREW TAP TITE(P) BRAZIER 3*12 BK AE008990 810923080S SCREW TAP TITE(B) BIND 3*8 BK...
Page 78
DVD DECK REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description ! 600 AE008975 A5Z001B650 DVD MECHA ASS'Y A5Z001B650 AE008499 92SBB0033A LOADER SUB ASS'Y DLM1D29-31 AE005815 92AAA0017A FEED RACK ASS'Y AE003551 92P100088A GEAR,MOTOR AE005805 92P100117A GEAR,MIDDLE AE008500 92P200017A INSULATOR, F AE008501 92P200018A INSULATOR, R...
Page 85
Digital Media Network Company Sales & Marketing Planning Div. International Customer Service & Support Dept. [33F-C] 1-1,SHIBAURA 1-CHOME, MINATO-KU TOKYO 105-8001,JAPAN PHONE:(03)3457-3536 FACSIMILE:(03)5444-9403 SERVICE INSTRUCTION File No. 81C-200719 Date: 27, June, 2007 Product: LCD TV/DVD combination Model: 15DLV77 Subject : Correction of wrong Service part on Service manual Location Part No reference No...
Page 87
FILE NO. 810-200688GR SERVICE MANUAL 15-inch Diagonal LCD TV/DVD COMBINATION 15DLV77 The above model is classified as a green product (*1), as indicated by the underlined serial number. This Service Manual describes replacement parts for the green product. When repairing this green product, use the part(s) described in this manual and lead-free solder (*2).
Page 88
DVD BLOCK DIAGRAM LCD BLOCK DVD LOADER DSM2 C, D DVD/CDPD RF_A, B, C, D, E, F START_SW SPDIF DVD/CD, DVD_LD, CD_LD MPEG/MICON/DSP/RF_AMP DVD C IC4001 DVD Y TR+/-, FO+/-, SPINDLE/SLED/ ZR36882ELCG MOT_LD+/-, FOCUS/TRACK_PWM, DVD RESET MOT_SLED+/-, Motor Drive TRAY_CLOSE/OPEN SPINDLE/ MOT_SPDL+/- IC2301...
Page 89
TUNER BLOCK DIAGRAM INVERTER CP505 V IN F501 L509 V IN V IN AC IN INVERTE_H TRANSFORM T501 D504 DVD +12V DVD MPEG DVD +12V C509 AT+12V SOUND+B D511 DC-DC 5V SW FET AT+5V POWER SW DC-DC Q509 IC501 STR-W6735 F502 4V SW FET SW+4V...
POWER2 SCHEMATIC DIAGRAM SH501 SH502 TP00370-21 (POWER PCB) TP00370-21 FROM/TO INVERTER (CD7001) SBC4-4R7-582 CP505 L504 A2001WV2-8P V IN 4.7uH TSL0808 V IN L503 22uHTSL0808 V IN GND(B.L) L501 GND(B.L) R533 COIL,LINE FILTER GND(B.L) L509 22uHTSL0808 0.047 1/4W SS24H-10100 W805 TSL0808 13.9 R548 INVERTER_H...
Page 118
INVERTER SCHEMATIC DIAGRAM (BACK LIGHT PCB) FROM/TO POWER2 CD7001 (CP505) 4A 48V CU281801 F7001 T7001 CRT-057 V IN -0.4 1206FA4A-T DRIVE Q7001 FDS4685 V IN 4A 48V V IN 11.9 T7005 AW-HA284T GND(B.L) CP7001 1565647-2 GND(B.L) 11.9 -0.4 L7002 HIGH GND(B.L) C7021 I-PWM...
Page 119
SW SCHEMATIC DIAGRAM (SW PCB) ESE22MH22 CD2301 2H061605 GND(SW) PICK UO INNER LIMIT SWITCH FEED MOTOR(-) M2602 BCZ3B05 FEED MOTOR(+) SPINDLE MOTOR(-) M2601 SPINDLE MOTOR(+) JCV9B12 PCB640 DED020 NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE H-39 H-40...
WAVEFORMS FRONT END 0.5V 200mV 200mV AV SWITCH/JACK MICON 50ns 0.5V 200mV 500mV SOUND AMP VIDEO AD 10µs 0.5ms 10µs 0.5V 1.0V 100mV 50µs 10µs 0.5V 1.0V 200mV 10µs 0.5V 50mV 100mV FRONT END 20µs 200mV 50mV 500mV 20µs 200mV 200mV 500mV The following waveforms were measured...
Page 123
WAVEFORMS 100mV 10µs 50mV 10µs 50mV 10μs 50mV 10µs 50mV 10µs 50mV 10µs 50mV The following waveforms were measured NOTE: at the point of the corresponding balloon number in the schematic diagram.