Channel/Clock Settings When Tv Guide On Screen; System Is Not Used; Auto Channel/Clock Settings - Panasonic DMR-EH55S Operating Instructions Manual

Channel/Clock settings when TV Guide On Screen

Refer to the control reference on page 60.
Preparation:
If the program listings have already been downloaded, return the unit to the factory preset condition using the steps indicated below.
When the unit is on and stopped
1 Press and hold [X CH] and [W CH] on the main unit for about five
seconds.
The unit turns off.
2 Press [POWER Í/I] to turn the unit on.
3 After the language and TV aspect is set up, press [RETURN] and
exit the TV Guide On Screen
[Note]
You can record only manually after you set the unit with "Set Channels Automatically".

Auto channel/clock settings

1
While stopped
Press [FUNCTIONS].
2
Press [3, 4] to select "Other
Functions" and press [ENTER].
3
Press [3, 4] to select "Setup" and
press [ENTER].
4
Press [3, 4] to select "Channel" and
press [1].
5
Press [3, 4] to select "Set Channels
Automatically" and press [ENTER].
6
Press [ENTER].
Auto Channel Setting starts. This takes a few minutes.
The unit then proceeds with Auto Clock Setting. The time is
displayed when finished.
Setup
Channel
Setup
Disc
Video
Audio
≥DST, Daylight Saving Time, shows the summertime setting.
Regarding DST (Daylight Saving Time) ➡ 22
≥TIME ZONE shows the time difference from Greenwich
Mean Time (GMT).
EST (Eastern Standard Time) l GMT j5
CST (Central Standard Time)
MST (Mountain Standard Time) l GMT j7
PST (Pacific Standard Time)
AST (Alaska Standard Time)
HST (Hawaii Standard Time)
For other areas: xx hr
≥If the Auto Clock Setting does not start automatically, select
"Clock Settings" from the "Setup" tab and then select "Set
Clock Automatically".
≥If the time was not set correctly, use "Set Clock Manually"
(➡ 22) or adjust time zone.
7
Press [ENTER].
To return to the previous screen
Press [RETURN].
To exit the screen
Press [RETURN] several times.
To cancel partway while Auto Channel/Clock Setting is taking place
Press [RETURN].
To set so the TV Guide On Screen
RQT8365
When the power is turned on and the Start setup screen is displayed, press [3, 4] to select "Don't remind me again" and press [ENTER].
64
TM
system setup screen.
Set Clock Automatically
Auto Clock Setting is complete.
4/4/2005 12:15 AM
DST.............. On
Time Zone..... CST
l GMT j6
l GMT j8
l GMT j9
l GMT j10
TM system is not displayed automatically when you turn the unit on
TM

system is not used

POWER
S VIDEO VIDEO
DV IN
POWER Í/ l
≥The unit configures channels according to the Signal Source
(RF IN) settings as follows.
Signal Source
(RF IN)
VHF
Antenna
UHF
VHF
CATV LOW BAND
CATV MID/SUPER BAND
CableTV
CATV HYPER BAND
ULTRA BAND
SPECIAL CATV CHANNEL
Adjust Time Zone
Adjust the time zone (j1 or i1) if it was not set correctly with auto
clock setting.
You cannot change this setting if you set the clock manually.
1
While stopped
Press [FUNCTIONS].
2
Press [3, 4] to select "Other
Functions" and press [ENTER].
3
Press [3, 4] to select "Setup" and
press [ENTER].
4
Press [3, 4] to select "Setup" and
press [1].
5
Press [3, 4] to select "Clock
Settings" and press [ENTER].
6
Press [3, 4] to select "Adjust Time
Zone" and press [ENTER].
Setup
Adjust Time Zone
Channel
Setup
Disc
Video
7
Press [3, 4] to select "s1" or "r1"
and press [ENTER].
X CH W
DRIVE REC
OPEN/CLOSE
SELECT
k1.3
CH 1.3
L/MONO-AUDIO-R
IN2
Band Channel
2–13
14–69
2–13
95–99
14–36
37–65
66–94
100–125
1
j1
0
i1