Channel/Clock Settings When Tv Guide On Screen; System Is Not Used; Auto Channel/Clock Settings - Panasonic DMR-EH60 Operating Instructions Manual

Channel/Clock settings when TV Guide On Screen

Refer to the control reference on page 54.
Preparation:
If the television program list has already been downloaded, return the unit to the factory preset condition using the steps indicated below.
When the unit is on and stopped
1 Press and hold [X CH] and [W CH] on the main unit for about five
seconds.
The unit turns off.
2 Press [Í DVD POWER] to turn the unit on.
3 Complete the TV Guide On Screen
is pressed after the "Watch TV" message screen is displayed).
[Note]
You can set scheduled recording only manually after you set the unit with "Set Channels Automatically".

Auto channel/clock settings

1
Press [SETUP].
2
Press [3, 4] to select "Channel" and
press [1].
3
Press [3, 4] to select "Set Channels
Automatically" and press [ENTER].
4
Press [2, 1] to select "Yes" and
press [ENTER].
5
Press [ENTER].
Auto Channel Setting starts. This takes a few minutes.
The unit then proceeds with Auto Clock Setting. The time is
displayed when finished.
SETUP Set Clock Automatically
Auto Clock Setting is complete.
Channel
Setup
4/4/2005 12:15 AM
Disc
DST.............. On
Time Zone..... CST
Video
Audio
≥DST, Daylight Saving Time, shows the summertime setting.
≥TIME ZONE shows the time difference from Greenwich
Mean Time (GMT).
EST (Eastern Standard Time) l GMT j5
CST (Central Standard Time)
MST (Mountain Standard Time) l GMT j7
PST (Pacific Standard Time)
AST (Alaska Standard Time)
HST (Hawaii Standard Time)
For other areas: xx hr
≥If the Auto Clock Setting does not start automatically, select
"Clock Settings" from the "Setup" tab and then select "Set
Clock Automatically".
≥If the time was not set correctly, use manual clock setting
(➡ 17) or adjust time zone.
6
Press [ENTER].
To return to the previous screen
Press [RETURN].
To exit the screen
Press [SETUP].
To cancel partway while Auto Channel/Clock Setting is taking place
Press [RETURN].
To set so the television program list is not displayed automatically when you turn the unit on
➡ 29, "Review Options" menu–Selecting the TV Guide On Screen
TM system setup (until [ENTER]
l GMT j6
l GMT j8
l GMT j9
l GMT j10
TM
system start up pattern
TM

system is not used

X CH W
HDD DVD SD
C H C H
S VIDEO S VIDEO VIDEO VIDEO L/MONO L/MONO-AUDIO AUDIO-R
DV DV I N I N I N 2 I N 2
≥The unit configures channels according to the Signal Source
(RF IN) settings as follows.
Signal Source
(RF IN)
VHF
Antenna
UHF
VHF
CATV LOW BAND
CATV MID/SUPER BAND
CableTV
CATV HYPER BAND
ULTRA BAND
SPECIAL CATV CHANNEL
Adjust Time Zone
Adjust the time zone (j1 or i1) if it was not set correctly with auto
clock setting.
You cannot change this setting if you set the clock manually.
1
Press [SETUP].
2
Press [3, 4] to select "Setup" and
press [1].
3
Press [3, 4] to select "Clock
Settings" and press [ENTER].
4
Press [3, 4] to select "Adjust Time
Zone" and press [ENTER].
SETUP
Adjust Time Zone
Channel
Setup
Disc
Video
5
Press [3, 4] to select "s1" or "r1"
and press [ENTER].
DRIVE DRI VE
REC REC
OPEN/CLOSE OPEN/CLOSE
SELECT SELECT
/x1.3
Band Channel
2–13
14–69
2–13
95–99
14–36
37–65
66–94
100–125
1
j1
0
i1
RQT8307
57