Panasonic DMR-EH55S Operating Instructions Manual page 21

Please perform setup by following all instructions that apply to your current service.
DirecTV/DISH Network service is only available in the United States and is not available or
supported in Canada.
Service
≥You cannot select both "Antenna" and "Cable without a Cable Box".
Antenna
≥Further setup is not necessary.
Cable without
a Cable Box
1 Cable box connection channel ("RF, Channel 2"/ "RF, Channel 3"/ "RF, Channel 4"/ "IN3")
–"IN3" is the usual selection.
(If you are connecting the cable box to this unit's RF terminal, select "RF, Channel 2", "RF, Channel 3" or "RF,
Channel 4", according to the cable box setting.)
2 Are you using a digital service package?
Select "Yes", "No" or "I don't know".
3 Check how the channels are input.
Select how your current cable box inputs 2, 3, and 4-digit numbered channels.
4 Cable box brand
–Move down with [4] for more brands.
–You can also press [PAGE W] or [PAGE X] to skip several lines.
5 IR signal code
–Make sure your cable box is set to the channel that appears on screen and press [ENTER].
Cable with a
Cable Box
1 Satellite receiver connection channel ("RF, Channel 2"/ "RF, Channel 3"/ "RF, Channel 4"/ "IN3")
–"IN3" is the usual selection.
(If you are connecting the satellite receiver to this unit's RF terminal, select "RF, Channel 2", "RF, Channel 3" or
"RF, Channel 4", according to the satellite receiver setting.)
2 Check how the channels are input.
Select how your current DirecTV receiver inputs 2, 3, and 4-digit numbered channels.
3 Satellite receiver brand
–Move down with [4] for more brands.
–You can also press [PAGE W] or [PAGE X] to skip several lines.
4 IR signal code
–Turn your satellite receiver ON and press [ENTER].
DirecTV
≥Satellite receiver connection channel ("RF, Channel 2"/ "RF, Channel 3"/ "RF, Channel 4"/ "IN3")
–"IN3" is the usual selection.
(If you are connecting the satellite receiver to this unit's RF terminal, select "RF, Channel 2", "RF, Channel 3" or
DISH Network
"RF, Channel 4", according to the satellite receiver setting.)
You cannot use the IR Blaster included with this unit.
You cannot set other equipment.
Once setup is finished ➡ 22, Step 7, Confirm the settings.
The unit begins trying various IR codes to see which one communicates properly with your cable box. It's quite
common for this phase of the setup to be repeated numerous times.
Is your cable box now tuned to channel 09?
Yes
No
Test this code again
–If the cable box has changed to channel 09, select "Yes".
–If the cable box is still set to the same channel, select "No". Repeat this step until the cable box changes to
channel 09.
–If you want to try the code again for some reason, e.g., you accidentally moved the IR Blaster, select "Test
this code again".
If you are watching DirecTV in 4:3 aspect with the side panel, set the side panel to "Off" on the
DirecTV receiver in order to correctly receive the program listings.
The unit begins trying various IR codes to see which one communicates properly with your satellite receiver.
It's quite common for this phase of the setup to be repeated numerous times.
Did your satellite receiver change channels ?
Yes
No
Test this code again
Look at the display of the DirecTV receiver.
–If the channel display has changed, then select "Yes".
–If the satellite receiver is still set to the same channel, select "No". Repeat this step until the satellite receiver
changes the channel.
–If you want to try the code again for some reason, e.g., you accidentally moved the IR Blaster, select "Test
this code again".
Set the following
RQT8365
Continued on next page
21