Nikon Flash Units That Can Be Used - FujiFilm Finepix S2 Pro Owner's Manual

NIKON FLASH UNITS THAT CAN BE USED

The Nikon flash models listed in the table below can be used with this camera. In the table, 1
indicates D- or G-type Nikkor lenses (except IX-Nikkor), 2 indicates CPU Nikkor lens other
than D- or G-type (except AF Nikkor for F3AF) and 3 indicates non-CPU Nikkor lenses.
Flash mode
TTL
3D Multi- Sensor Multi- Sensor
Balanced Fill- Balanced Fill-
Flash
✽1
Lens Flash Flash
1 u
SB-28, SB-28DX
✽1
2 u
(Cordless)
3
u
1
✽1
SB-27 (Cordless) 2 u
3
1 u
✽4 ✽1
SB-26 (Cordless) 2 u
3
1 u
✽1
SB-25 (Cordless) 2 u
3
✽1
1 2
u
SB-24 (Cordless)
3
✽6
✽5
SB-23, SB-29 1 2 u
✽5
SB-21B
(Cordless) 3
✽6
SB-22s, SB-22, 1 2 u
SB-20, SB-16B,
SB-15 (Cordless) 3
✽6
1 2 u
✽7
SB-11 , SB-14
3
✽1 metering system other than Spot.
✽2 Standard TTL is performed with Spot Metering. Also, selecting Manual exposure mode automatically changes the
TTL Auto Flash mode to Standard TTL with flash other than SB-28/28DX, 27, 26, 25 and 24 that are equipped with
TTL Auto Flash.
✽3 When Spot metering is selected, Monitor Pre-Flash will not be fired.
✽4 Wireless Slave Flash can be performed with the SB-26. Shutter speed is automatically controlled to slower than
1/90 sec. when the Wireless Slave Flash selector is set to D.
✽5 With the SB-29 and SB-21B, autofocus can only be used when an AF Micro-Nikkor (60 mm, 105 mm, 200 mm and
70-180 mm) is attached.
✽6 Select exposure mode other than Manual or metering system other than Spot.
✽7 If TTL mode is used with the SB-11 or SB-14, the SC-23 TTL flash control cord is required for the connection, To
use "A" or "M" mode, connect the SB-11 or SB-14 with the SC-13 and SU-2. The SC-11 or SC-15 can also be
used to connect the SB-11 or SB-14, but in that case the Ready light in the camera's viewfinder display cannot be
used and the shutter speed is not selected automatically.
I Notes on using Nikon flash units
h Refer to the instructions supplied with the flash unit for details.
If your flash unit supports TTL mode and comes with instructions that include a table of
camera types, refer to the section for group I cameras.
h The synchronized shutter speed when a flash is used is a slow speed of 1/125 sec. or slower.
h In TTL mode, the ISO sensitivity linked settings are ISO 100-400.
h With the SB-26, 25 or 24, flash sync mode set on the Speedlight overrides the setting on the
camera body.
h If you set the camera's synchro mode to "Red-eye Reduction" or "Red-eye Reduction Slow
Synchro" and then use a Nikon external flash unit that has its own red-eye reduction function,
the red-eye reduction lamp on the external flash unit fires.
68
A M
Standard Rear-
Non-TTL Repeating Red-Eye
TTL Manual Curtain
Auto Flash Reduction
✽2
flash Sync
u u u u u u
u u u u u u
u u u u u u
u u u u u
u u u u u
u u u u u
u u u u u u
u u u u u u
u u u u u u
u u u u u u
u u u u u u
u u u u u u
u u u u u u
u u u u u u
u u u u
u u u u
u u u u u
u u u u u
u u u u u
u u u u u
h Even when the optional flash with the AF-Assist Illuminator is attached, AF-Assist Illuminator
does not emit light unless the conditions for AF-Assist Illumination are met.
h With SK-6 and SB-24 are attached, AF-Assist Illuminators of the camera body and the flash
do not emit light.
h When the exposure mode is "P" Multi-Programmed Auto, the widest aperture that can be
Monitor
Pre- automatically set by the camera is governed by the ISO setting used, as shown in the table
✽3
Falsh
below.
u
ISO setting
u
Widest aperture (built-in flash)
u
u
Widest aperture (optional flash)
u
✽ If an aperture that is wider than the controlled aperture is still too dark, the aperture is determined by widest aperture
u
on the mounted lens.
u
h When flash exposure compensation is set, "
u
compensation value.
h " " in the top display panel and "P" in the viewfinder blink and the shutter cannot be
released when the exposure mode is set to "P" and attached flash is not set to TTL Auto
Flash. Set the flash mode to TTL, or set the camera's exposure mode to "S", "A" or "M".
h To cancel Monitor Pre-Flash when using the SB-28/28DX, 27, 26 or 25, select Spot metering.
N
Flash attachments made by manufacturers other than Nikon
Use only Nikon flash models. Other units may damage the camera's electrical circuit due to
incompatible voltage requirements (not compatible with 250V or higher), electric contact alignment
or switch phase.
I Accessory shoe (with cover)
An optional flash, i.e. SB-28/28DX, SB-27, SB-26, SB-25, SB-24, SB-23
or SB-22s can be attached directly to the accessory shoe of the FinePix S2 Pro without a cord.
This accessory shoe is equipped with a safetylock which prevents accidental drop when a flash
with a safety-lock pin (i.e. SB-28/ 28DX, SB-27, SB-26, SB-25 or SB-22s) is attached.
Always install the accessory shoe cover when you are not using an external flash unit.
I Synchronizing terminal (with cap)
To use an external flash unit that requires a synchro cord, connect the synchro cord to the
synchro cord terminal (with JIS-B locking screw). However, if you mount a Nikon SB-28/28DX,
SB-50DX, SB-28, SB-27, SB-26, SB-25, SB-24, SB-23, SB-22S or SB-29 on the accessory
shoe and then select Rear Synchro mode, do not connect other external flash units to the
synchronizing terminal to provide additional flash for the shot.
100 160 200
2.8 3.3 3.3
4 4.8 4.8
" appears in the viewfinder without the
N
400
4
5.6
3
69