Connecting To A Computer Via Usb; Disconnecting From The Pc (Important - Always Use This Procedure.) - FujiFilm Finepix S2 Pro Owner's Manual

CONNECTING TO A COMPUTER VIA USB

1
0 1 2 0
0 3
ＳＥＴ−ＵＰ ＳＥＴ−ＵＰ
ＦＲＡＭＥ ＮＯ． ＦＲＡＭＥ ＮＯ． ＯＦＦ ＯＦＦ
ＰＣ ＭＯＤＥ ＰＣ ＭＯＤＥ ＵＳＢ ＵＳＢ ＤＯＷＮＬＯＡＤＩＮＧ ＤＯＷＮＬＯＡＤＩＮＧ
ＢＥＥＰ♪ ＢＥＥＰ♪ ＬＯＷ ＬＯＷ
ＬＡＮＧＵＡＧＥ ＬＡＮＧＵＡＧＥ ＥＮＧＬＩＳＨ ＥＮＧＬＩＳＨ
ＤＡＴＥ／ＴＩＭＥ ＤＡＴＥ／ＴＩＭＥ ＳＥＴ ＳＥＴ
ＲＥＳＥＴ ＡＬＬ ＲＥＳＥＴ ＡＬＬ ＯＫ ＯＫ
ＯＫ ＯＫ ＢＡＣＫ ＢＡＣＫ
2
0 1 2 0
USB socket
USB
Camera
socket
G
!
In Windows XP and Mac OS X, automatic startup must be set up the first time you connect.
G
!
Take care to ensure that the cable is connected the right way round and that the plugs are firmly inserted all
the way into the sockets.
If you are using a Windows PC, the driver settings are automatically specified when installation
ends. Simply wait a few moments.
✽ If your computer does not recognize the camera, refer to the Software Quick Start Guide.
Camera Operations
h When the camera and the computer are
exchanging data, the Access lamp blinks
orange.
h "USB DOWNLOADING" is displayed on the
rear display panel.
h The Auto Power Off function is disabled
while the camera is connected to a
computer.
G
!
When replacing the SmartMedia, always disconnect
the camera and computer first using the procedure
described on P.103.
G
!
Do not disconnect the USB cable during
communication. See P.103 for the disconnection
102
instructions.
1Load a media containing photographed
images into the camera.
2Switch the camera on.
3Select "USB DOWNLOADING" as the "PC
MODE" setting in SET–UP (➡P.89).
4Set the power switch to "OFF" to switch the
camera off.
G
!
Before connecting, you must install software on the
bundled CD-ROM on your computer.
G
!
Use of the AC power adapter (sold separately) is
recommended when connecting the camera to a
computer.
G
!
If a SmartMedia and Microdrive are both loaded into the
camera at the same time, the media selected in the
"MEDIA" setting in SET–UP is used (➡"Setup", P.89).
1Switch your PC on.
2Connect the special USB cable to the camera
and the computer.
3Switch the camera on.
Always use the prescribed procedure when
disconnecting or switching off the camera
(➡P.103).
PC
PC Operations
h If FinePixViewer is installed, it starts up
automatically.
h A removable disk icon appears and you
can use your PC to transfer files to and
from the camera.
Windows Macintosh
If the above operations do not occur, you do
not have the required software programs or
drivers installed on your PC. Refer to the
Software Quick Start Guide booklet and
complete the required PC setup procedures.
Then reconnect the camera to your PC.
DISCONNECTING FROM THE PC ( Important — always use this procedure. )
1
Off
G
!
In some cases, the camera and computer may still be communicating even after the "Copying" message
disappears from the computer screen. Always check that the Access lamp is off.
Perform the steps shown below before you switch the camera off. This procedure differs
2
depending on the operating system software (or PC) you are using.
Windows 98/98 SE
For a USB connection, no action is needed on the computer.
If you are connecting via an IEEE1394 interface, use the disconnection procedure described
below.
1Left-click the Eject icon in the taskbar and eject "USB Disk".
2The "Eject" menu option is displayed. Click this menu option.
3The "Eject hardware" dialog box appears. Click the [OK] button or the close button.
Windows Me/2000 Professional/XP
1Right-click the removable disk icon in the
"My Computer" window and select Eject.
✽ This step is only required in
Windows Me.
Macintosh
Drag the "Removable drive" icon on the desktop to the Trash.
Switch the camera off and disconnect the IEEE1394 or USB cable.
3
1Quit all applications (FinePixViewer, etc.) that
are using the camera.
2Check that the Access lamp is off (that the
camera and computer are no longer
exchanging data).
2Left-click the Eject icon in the taskbar
and eject "USB Disk".
✽ Windows Me screen
3The "Eject" menu option is displayed.
Click this menu option.
4The "Eject hardware" dialog box appears.
Click the [OK] button or the close button.
G
!
When you drag the icon to the Trash, "REMOVE
OK" appears on the camera's screen.
6
103