Custom Setting (Csm); Cancelling Custom Settings; I Custom Settings List - FujiFilm Finepix S2 Pro Owner's Manual

CUSTOM SETTING ( CSM )
The custom settings allow to modify camera functions such as how information is displayed in
the viewfinder and which functions are assigned to which buttons.
1
2
ＣＵＳＴＯＭ ＳＥＴＴＩＮＧ ＣＵＳＴＯＭ ＳＥＴＴＩＮＧ
２． ２．ＯＮ−ＤＥＭＡＮＤ ＧＲＩＤ ＬＩＮＥＳ ＤＩＳＰＬ ＯＮ−ＤＥＭＡＮＤ ＧＲＩＤ ＬＩＮＥＳ ＤＩＳＰＬＡＹ ＡＹ
０ ＯＦＦ ＯＦＦ
１ ＯＮ ＯＮ
ＭＡＩＮ ＭＡＩＮ ＭＥＮＵ ＭＥＮＵ ＳＵＢ ＳＵＢ ＳＥＴＩＮＧ ＳＥＴＩＮＧ
0 1 0 2
0 3
When you have finished the settings, set the exposure mode dial to a setting other than
3
"CSM".
G
!
The custom settings are retained when the camera is switched off.

Cancelling custom settings

1 0
0 2 2 0
96
Set the exposure mode dial to "CSM".
1Turn the main-command dial to select an
option.
2Turn the sub-command dial to change the
setting.
3"
" appears on the top display panel.
1Set the exposure mode dial to "CSM".
2Hold down the " " and " " buttons together
for at least 2 seconds (green markings are
positioned alongside).
The top display panel flashes briefly and the
settings are reset.
h All the custom settings are reset to their
default values.
h The ISO sensitivity is reset to 200.

I Custom Settings List

No. Setting Display
0: METERED VALUE ➡
1
UNDER ➡ OVER (default)
BRACKETING ORDER
1: UNDER ➡ METERED
VALUE ➡ OVER
2 ON-DEMAND GRID LINES 0: OFF (default)
DISPLAY 1: ON
3 ILLUMINATION FOR 0: AUTO (default)
FOCUS AREA 1: OFF
2: ON
4 FOCUS AREA SELECTION 0: NORMAL (default)
1: ENABLES
ROTATION
5 AE-LOCK 0: DISABLED (default)
1: ACTIVATED
6
LONG EXP. (BULB) AT 0: DISABLED (default)
MANUAL MODE 1: ACTIVATED
7
CLOSEST-SUBJECT- 0: ENABLED (default)
PRIORITY DYNAMIC AF 1: DISABLED
AT S-AF MODE
8
CLOSEST-SUBJECT- 0: DISABLED (default)
PRIORITY DYNAMIC AF 1: ENABLED
AT C-AF MODE
9 AE/AF LOCK BUTTON 0: AE/AF LOCK
(default)
1: AE LOCK ONLY
2: AF LOCK ONLY
3: AE REMAINS
LOCKED
4: AF OPERATION
10 COMMAND DIAL 0: DISABLED (default)
FUNCTIONS 1: ENABLED
11 MULTIPLE EXPOSURE 0: SINGLE SHUTTER
RELEASE (default)
1: CONTINUOUS
SHUTTER
RELEASE
Details
Allows you to change the compensation sequence
when auto exposure bracketing is used.
If you display the framing guides, you can use the
intersections of the horizontal and vertical lines to
position your main subject in the shot or align one of the
horizontal lines with the horizon. This allows you to
compose the desired shot while monitoring the subject's
size and the balance.
Specifies the illumination used for the focus area in the
viewfinder.
Selecting cyclic focus area selection allows you to
select the opposite focus area without changing which
part of the 4-direction button you have to press.
This setting lets you apply AE lock by pressing the
shutter button down halfway.
Select "1" to take bulb flash shots in the "M" exposure
mode.
If you select "1", Closest-subject Priority Dynamic AF is
not used in AF-S mode.
If you select "1", Closest-subject Priority Dynamic AF is
used in AF-C mode.
Normally, AE lock (exposure recording) and AF lock
(focus lock) are both applied concurrently when you
press the "AE-L/AF-L" button. However, this can be
changed so that only AE lock or only AF lock is applied,
or so that that the AE lock status is maintained. If the
AE/AF lock is used with the "Maintain AE lock" setting,
pressing the "AE-L/AF-L" button again or releasing the
shutter cancels the lock.
In addition, though the auto focus (AF) normally
operates when the shutter button is pressed down
halfway, you can change this so that AF operates when
the "AE-L/AF-L" button is pressed. (In this case, AF
does not operate when the shutter button is pressed
down halfway.)
Use this setting to change the main command dial and
sub-command dial operation during photography.
0: Main: Changes the shutter speed.
Sub: Changes the aperture.
1: Main: Changes the aperture.
Sub: Changes the shutter speed.
Changing this setting allows you to use continuous
shooting for multi-exposure shots.
5
97