Table of Contents
Advertisement
[07] Closing (Arming) Reporting Codes
Partial Closing Reporting Code
Reporting codes 1 to 6 are used to identify closings for access
codes 1 to 6. If partial closing is identified in Section [14], then
alarm codes for manually bypassed zones will be transmitted
when the system is closed with one or more zones bypassed.
When transmitting in 4/2, 3/1 or any other of the extended
formats, see Section [05] above. The 6 closing codes are
programmed as follows:
[C1], [C2], [C3], [C4], [C5], [C6]
Where the first digit HEX 'C' represents a closing signal and
the second digit represents the user access code which was
used to arm the system (HEX 'C' could be any other number
depending on what is used at the monitoring station).
The closing code transmission takes place after the Exit
Delay time. Therefore, if the system is armed and disarmed
before the expiry of the exit time, no closing transmission will
take place.
The partial closing code, if used, is transmitted in tandem
with the regular closing code to identify the closing as a
partial closing.
When the system has been armed using the Quick-Arm
∗
command [
][0] or using the Auto-Arm feature, access
code #1 will be transmitted.
[08]
Opening (Disarming) Reporting
Codes After Alarm Reporting Code
The first 6 reporting codes correspond to the 6 user access
codes. When the system is disarmed using one of the access
codes, the corresponding reporting code in this section is
transmitted. See Section [07] above for examples of reporting
code programming.
If the After Alarm Code is programmed, that code will be
transmitted to the monitoring station on opening if an alarm
occurred during previous armed period. This feature is
useful for installations where openings and closings are not
reported normally, but it is desired to have a report to the
monitoring station on opening if an alarm did occur during the
previous armed period. This feature allows the monitoring
station to know when the user is on the premises and available
to receive a report about alarms while the system was closed.
[09] Priority Alarms and Restorals
These reporting codes are used by the communicator to
transmit the following list of troubles, alarms and restorals.
See Section [05] as a guide for programming.
• Fire Zone Trouble.
• Keypad [P]anic Alarm.
• Keypad [F]ire Alarm.
• Keypad [A]uxiliary Alarm.
• Fire Zone trouble Restore.
• Keypad [P]anic Restore.
• Keypad [F]ire Restore.
• Keypad [A]uxiliary Restore.
Transmission for operation of the [F], [A] and [P] keys will only
take place if the appropriate sections in [09] are programmed
with a reporting code.
12
[10] Maintenance Alarms and Restorals
These reporting codes are used by the communicator to
transmit the following list of alarms and restorals. See Section
[05] as a guide to programming.
• Low Battery Alarm.
• AC Failure Alarm.
• Fuse Failure Alarm.
• Low Battery Rrestore.
• AC Failure Restore.
• Fuse Failure Restore.
• Automatic Test Code
The Test Code is not transmitted if periodic downloading is
selected, Section [14], light 3. For Automatic Test Code
Reporting, the time between reports (in days) must be
entered in Section [17] and the time of day for the report must
be entered in Section [19].
[11]
Zone Definitions
As in the reporting codes sections, once this section is
entered, 6 2-digit numbers are required.
number entered defines how a zone will operate.
Zone Definitions Digit #1
The first digit determines whether the zone will cause a silent
alarm or an audible alarm and whether the zone response will
be fast or slow. Zone response time can be programmed in
Section [17] and can be set from 10 ms to 990 ms The factory
default zone response time is 500 ms. If set at fast, the zone
response time is 10 ms, and if set at slow, the zone response
time is 500 ms or whatever time is set in Section [17].
[0] = slow & audible
[1] = slow & silent
[2] = fast & audible
[3] = fast & silent
Zone Definitions Digit #2
Digit #2 determines the zone type, [0] through [8], as
described below.
[0] Standard Delay Zone has an Entry and Exit Delay and
is normally used for entry/exit doors. The Exit Delay starts
as soon as the panel is armed. The zone may be opened
and closed during the delay time without causing an
alarm. After the Exit Delay time has expired, opening the
zone will start the Entry Delay timer. During the Entry
Delay time, the keypad buzzer will sound steadily to
advise the user that the system should be disarmed. If the
panel is disarmed before the entry time expires, no alarm
will be generated.
The default times for this type of zone are a 30 second
Entry Delay and a 120 second Exit Delay. The Entry and
Exit Delays may be independently programmed in Section
[17] for periods from 1 second to 255 seconds. All zones
programmed as type [0] will have the Entry and Exit
Delays as programmed in Section [17] or the default
times if Section [17] is not programmed.
[1] Instant Zone is normally used for door and window
contacts and has the standard Exit Delay but is instant
when opened after the Exit Delay expires. The Exit Delay
will be the default time of 120 seconds or the time as
established in programming Section [17].
Each 2-digit
Advertisement
Table of Contents
