Table of Contents
Advertisement
If a transmission is not wanted for a particular reporting code, then
enter '00' or 'FF' to disable that reporting code.
[06] Zone Restoral Reporting Codes
These reporting codes are used by the communicator to transmit zone
restorals for zones 1 through 6. Use instructions in section [05] above
as a guide for programming.
[07] Closing (Arming) Reporting Codes Partial
Closing Reporting Code
Reporting codes 1 to 6 are used to identify closings for access codes
1 to 6. If partial closing is identified in section [14], then alarm codes
for manually bypassed zones will be transmitted when the system is
closed with one or more zones bypassed.
When transmitting in 4/2, 3/1 or any other of the extended formats, see
section [05] above. The 6 closing codes are programmed as follows:
[C1], [C2], [C3], [C4], [C5], [C6]
Where the first digit HEX 'C' represents a closing signal and the second
digit represents the user access code which was used to arm the
system (HEX 'C' could be any other number depending on what is used
at the monitoring station).
The closing code transmission takes place after the exit delay time.
Therefore, if the system is armed and disarmed before the expiry of the
exit time, no closing transmission will take place.
The partial closing code, if used, is transmitted in tandem with the
regular closing code to identify the closing as a partial closing.
When the system has been armed using the Quick-Arm command
[ ][0] or using the Auto-Arm feature, access code #1 will be transmitted.
[08] Opening (Disarming) Reporting Codes After
Alarm Reporting Code
The first 6 reporting codes correspond to the 6 user access codes.
When the system is disarmed using one of the access codes, the
corresponding reporting code in this section is transmitted. See
section [07] above for examples of reporting code programming.
If the After Alarm Code is programmed, that code will be transmitted to
the monitoring station on opening if an alarm occurred during previous
armed period. This feature is useful for installations where openings
and closings are not reported normally, but it is desired to have a report
to the monitoring station on opening if an alarm did occur during the
previous armed period. This feature allows the monitoring station to
know when the user is on the premises and available to receive a report
about alarms while the system was closed.
[09] Priority Alarms and Restorals
These reporting codes are used by the communicator to transmit the
following list of troubles, alarms and restorals. See section [05] as a
guide for programming.
• Fire loop trouble.
• Keypad [P]anic alarm.
• Keypad [F]ire alarm.
• Keypad [A]uxiliary alarm.
Transmission for operation of the [F], [A] and [P] keys will only take
place if the appropriate sections in [09] are programmed with a
reporting code.
[10] Maintenance Alarms and Restorals
These reporting codes are used by the communicator to transmit the
following list of alarms and restorals. See section [05] as a guide to
programming.
• Low battery alarm.
• AC failure alarm.
• PTC failure alarm.
• Automatic Test Code
Test code is not transmitted if periodic downloading is selected,
section [14], light 3. For Automatic Test Code Reporting, the time
between reports (in days) must be entered in section [17] and the time
8
• Fire loop trouble restore.
• Keypad [P]anic restore.
• Keypad [F]ire restore.
• Keypad [A]uxiliary restore.
• Low battery restore.
• AC failure restore.
• PTC failure restore.
of day for the report must be entered in section [19].
NOTE: For UL installations, either AC failure or battery trouble reporting
must be enabled.
[11] Zone Definitions
As in the reporting codes sections, once this section is entered, 6 2-
digit numbers are required. Each 2-digit number entered defines how
a zone will operate.
Zone Definitions Digit #1
The first digit determines whether the zone will cause a silent alarm or
an audible alarm and whether the zone response will be fast or slow.
Loop response time can be programmed in section [17] and can be set
from 10ms to 2550ms The factory default loop response time is 500 ms.
If set at fast, the loop response time is 10 ms, and if set at slow, the loop
response time is 500 ms or whatever time is set in section [17].
Digit # 1 Summary
[0] = slow & audible
[1] = slow & silent
[2] = fast & audible
[3] = fast & silent
Zone Definitions Digit #2
Digit #2 determines the zone type, [0] through [8], as described below.
[0] Standard Delay Loop has an entry and exit delay and is normally
used for entry/exit doors. The exit delay starts as soon as the panel
is armed. The loop may be opened and closed during the delay time
without causing an alarm. After the exit delay time has expired,
opening the loop will start the entry delay timer. During the entry
delay time, the keypad buzzer will sound steadily to advise the user
that the system should be disarmed. If the panel is disarmed before
the entry time expires, no alarm will be generated.
The default times for this type of loop are a 30 second entry delay
and a 120 second exit delay. The entry and exit delays may be
independently programmed in section [17] for periods from 001
second to 255 seconds. All loops programmed as type [0] will have
the entry and exit delays as programmed in section [17] or the
default times if section [17] is not programmed.
[1] Instant Loop is normally used for door and window contacts and
has the standard exit delay but is instant when opened after the exit
delay expires. The exit delay will be the default time of 120 seconds
or the time as established in programming section [17].
[2] Interior Loop is normally used with interior motion detectors and has
the standard exit delay time. The loop also has the standard entry
delay time provided that a delay loop has been tripped first. If the
premises are entered without coming through a "delay" entrance,
and a type [2] loop is tripped, an immediate alarm will be generated.
[3] Interior Home-Away Loop operates the same as the type [2] loop
with the following exception. If the system is armed and the delay
loop is NOT tripped during the exit delay time, the type [3] loop will
be bypassed. Instead of the interior portion of an interior Home-
Away loop, a Home-Away loop can have a delay equal to the
standard entry and exit delay when section [32], light 3 is ON. This
will affect all Home-Away zones when they are not bypassed by
[ ][1][ ][9] arming, or by arming and not leaving the premises. If
Home-Away zones are automatically bypassed or [ ][9] arming
bypassed and the user then enters [ ][1], the Home-Aways will
then have a delay.
[4] 24 Hour Bell Loop is active at all times and will create an alarm if
the panel is armed or disarmed. This loop will always activate the
bell/siren output, unless programmed as silent in digit #1 of the
zone definition.
[5] 24 Hour Bell/Buzzer operates as the type [4] except the bell/siren
output is activated only when the panel is armed and only the
keypad buzzer is activated while the panel is disarmed.
[6] 24 Hour Buzzer operates as the type [4] except only the buzzer will
be activated in the armed or disarmed mode.
Advertisement
Table of Contents
