Xerox Nuvera 100 Getting Started Manual
Hide thumbs
Also See for Nuvera 100:
- Software manual (498 pages) ,
- Service manual (304 pages) ,
- Installation planning manual (242 pages)
Related Manuals for Xerox Nuvera 100
Summary of Contents for Xerox Nuvera 100
- Page 1 Software Version 10.0 October 2009 701P49976 ® Xerox Nuvera Getting Started Guide Xerox Nuvera 100/120/144 EA/MX Production System Xerox Nuvera 200/288 EA/MX Perfecting Production System...
- Page 2 ©2009 Xerox Corporation. All rights reserved. Xerox® and the sphere of connectivity design, Xerox Nuvera® and FreeFlow® are trademarks of Xerox Corporation in the United States and/or other countries. ENERGY STAR® and the ENERGY STAR mark are registered U.S. marks.
-
Page 3: Table Of Contents
European Union........................xvi Additional Information ....................xviii Introduction....................1-1 About this Guide ..........................1-1 Contents ...........................1-1 Xerox Nuvera EA/MX Production System ................1-2 Xerox Nuvera EA/MX Perfecting Production System ............1-3 Xerox FreeFlow Print Server User Interface .................1-4 Menus ............................1-5 The Status Area ........................1-5 Getting Started Guide... - Page 4 Table of Contents Your Learning Resources...............2-1 The Customer Materials Kit......................2-1 FreeFlow Print Server Help ......................2-1 Online Support Assistant.......................2-2 User Guide and Training Aid (UGTA) ..................2-3 Additional training...........................2-4 Providing Feedback .........................2-4 Getting Started Guide...
-
Page 5: Safety And Notices
Safety and Notices This Xerox Nuvera Printer Family and the recommended supplies are designed and tested to meet strict safety requirements. These include safety agency approval and compliance to established environmental standards. Please read the following instructions carefully before operating the product, and refer to them as needed to ensure the continued safe operation of your Xerox Nuvera Printer. -
Page 6: Radio Frequency Emissions
Changes or modifications to this equipment not specifically approved by the Xerox Corporation may void the user's authority to operate this equipment. -
Page 7: Safety Extra Low Voltage Approval
All system ports meet the Safety Extra Low Voltage (SELV) circuits for connection to customer-owned devices and networks. Additions of customer-owned or third party accessories that are attached to the Xerox Nuvera Printer must meet or exceed the requirements previously listed. All modules that require external connection must be installed per the installation procedure. -
Page 8: Usa
Xerox ENERGY STAR equipment is preset at the factory. Your machine will be delivered with the timer for switching to Power Save Mode from the last copy/print out, set at 8 minutes. A more detailed description of this feature can be found in the Maintenance Section of this guide. -
Page 9: Certifications In Europe
Safety and Notices Certifications in Europe The CE mark applied to this equipment symbolizes Xerox’s declaration of conformity with the following applicable Directives of the European Union as of the dates indicated: December 12, 2006 Council Directive 2006/95/EC as amended. Approximation of the laws of the member states related to low voltage equipment. -
Page 10: Electrical Safety
You may incur a severe electrical shock if the outlet is not grounded correctly. • Do not place the Xerox Nuvera Printer where people may step or trip on the power cord. • Do not place objects on the power cord. -
Page 11: Electrical Supply
Xerox Nuvera Safety and Notices Electrical Supply This product shall be operated from the type of electrical supply indicted on the product’s data plate label. If you are not sure that your electrical supply meets the requirements, please consult a licensed electrician for advice. -
Page 12: Laser Safety
This product contains laser-warning labels. These labels are intended for use by the Xerox Service Representative and are placed on or near panels or shields that require special tools for removal. -
Page 13: Operational Safety
Your attention to the following safety guidelines will help ensure the continued safe operation of your Xerox Nuvera Printer: • Use the materials and supplies specifically designed for your Xerox Nuvera Printer. The use of unsuitable materials may result in poor performance of the machine and possibly a hazardous situation. -
Page 14: Maintenance Information
Do not remove covers or guards that are fastened with screws. There are no parts behind these covers that you can maintain or service. Note Your Xerox machine is equipped with an energy saving device to conserve power when the machine is not in use. The machine may be left on continuously. WARNING The metallic surfaces in the fuser area are hot. -
Page 15: Ozone Information
Life Disposal USA and Canada If you are managing the disposal of your Xerox product, please note that the product contains lamp(s) with mercury, and may contain lead, perchlorate, and other materials whose disposal may be regulated due to environmental considerations. The presence of lead, mercury, and perchlorate is fully consistent with global regulations applicable at the time that the product was placed on the market. -
Page 16: European Union
In accordance with European legislation, end of life electrical and electronic equipment subject to disposal must be managed within agreed procedures. Prior to disposal, please contact your local dealer or Xerox representative for end of life take back information. Getting Started Guide... - Page 17 Xerox Nuvera Safety and Notices Battery Statement. These symbols on the products, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directive 2002/96/EC and 2006/66/EC.
-
Page 18: Additional Information
Europe: +44 1707 353 434 Other Countries: Please contact your local waste authorities and request disposal guidance. For USA questions and concerns, visit www.xerox.com and enter a term, such as PSDS, in the Search field. For product safety information outside the USA, visit www.xerox.com and use the change link to select the country of your choice. -
Page 19: Introduction
• The User Interface – Use the diagram to become familiar with the areas of the Xerox FreeFlow® Print Server user interface and read the information in the table to learn about the fault icons. -
Page 20: Xerox Nuvera Ea/Mx Production System
Introduction Xerox Nuvera Xerox Nuvera EA/MX Production System Use the following diagram to become familiar with the basic components of a Xerox Nuvera EA Production System. Configurations vary according to modules installed on the system. Control Console Optional Integrated DVD-RW Drive... -
Page 21: Xerox Nuvera Ea/Mx Perfecting Production System
Xerox Nuvera Introduction Xerox Nuvera EA/MX Perfecting Production System Use the following diagram to become familiar with basic components of a Xerox Nuvera EA/MX Perfecting Production System. Configurations vary according to modules installed on the system. One or Two Feed... -
Page 22: Xerox Freeflow Print Server User Interface
Xerox FreeFlow Print Server User Interface The Xerox FreeFlow Print Server software provides a user interface (UI) to control all of the features and functions for your Xerox Nuvera printing system. The UI consists of windows, tabs, and dialogs that can be accessed through buttons and menus. -
Page 23: Menus
Xerox Nuvera Introduction Menus The FreeFlow Print Server menus are located at the top of the interface and provide access to additional functions of the system. The menus are: • Logon - provides access to secured features of the Print Server. - Page 24 Introduction Xerox Nuvera Viewing additional information and settings The FreeFlow Print Server provides access to additional information through pop-up menus, Feature Access Buttons (FABs), and tabs. • Pop-up menus enable you to control functionality at the job or queue level and can be accessed by right-clicking or double-clicking on a particular job or list item.
-
Page 25: Your Learning Resources
Your Learning Resources There are a variety of resources available to help you learn about your new Xerox Nuvera System. The Customer Materials Kit The following items ship with every Xerox Nuvera System: • Getting Started Guide • System Administrator’s Guide (SAG) CD •... -
Page 26: Online Support Assistant
Xerox Nuvera Online Support Assistant To use the Online Support Assistant, go to www.xerox.com/support, type “Nuvera” in the text box and select [Search]. Select the [Support] link for your Xerox Nuvera model. The Online Support Assistant provides the following types of information: •... -
Page 27: User Guide And Training Aid (Ugta)
UGTA sections are provided below. The Resources screen The Search screen The Index is set up like displays a list of other Xerox allows you to search for the index of a book. All Nuvera documentation you... -
Page 28: Additional Training
Your Learning Resources Xerox Nuvera Additional training Additional training is available for your Xerox Nuvera EA/MX Production System and Xerox Nuvera EA/MX Perfecting Production System. If you would like to receive optional on-site training, contact your Xerox representative for more information. - Page 29 Getting Started Guide...