Xerox Nuvera 100 Getting Started Manual
Hide thumbs
Also See for Nuvera 100:
- Software manual (498 pages) ,
- Service manual (304 pages) ,
- Installation planning manual (242 pages)
Related Manuals for Xerox Nuvera 100
Summary of Contents for Xerox Nuvera 100
- Page 1 Software Version 9.0 October 2008 701P48794 ® ® Xerox Nuvera 100/120/144 EA Production System ® ® Xerox Nuvera EA Perfecting Production System Getting Started Guide...
- Page 2 DocuSP®, DigiPath®, and CentreWare®, VIPP® (Variable-data Intelligent PostScript Printware) and "Keep the Conversation Going. Share the Knowledge." are registered trademarks of Xerox Corporation in the US and/or other countries. Microsoft® is a registered trademark of Microsoft Corporation. Windows NT®, Windows® 2000, Windows® 2003, Windows® XP and Windows® Vista are registered trademarks of Microsoft Corporation.
-
Page 3: Table Of Contents
Ozone Information .......................8 Product Recycling & Equipment End of Life Disposal.............8 Introduction....................11 About this Guide ........................11 Xerox Nuvera EA Production System............12 Xerox Nuvera 288 Perfecting System ............13 The FreeFlow Print Server User Interface ..........14 The Default Screen......................14 Menus..........................15 The Status Area........................15 Your Learning Resources ................17... -
Page 5: Safety And Notices
Safety and Notices This Xerox Nuvera Printer Family and the recommended supplies are designed and tested to meet strict safety requirements. These include safety agency approval and compliance to established environmental standards. Please read the following instructions carefully before operating the product, and refer to them as needed to ensure the continued safe operation of your Xerox Nuvera Printer. -
Page 6: Radio Frequency Emissions
Changes or modifications to this equipment not specifically approved by the Xerox Corporation may void the user's authority to operate this equipment. : Shielded cables must be used with this equipment to WARNING maintain compliance with FCC regulations. -
Page 7: Product Safety Certification
Xerox ENERGY STAR equipment is preset at the factory. Your machine will be delivered with the timer for switching to Power Save Mode from the last copy/print out, set at 10 minutes. -
Page 8: Certifications In Europe
Authorized local dealer. : Changes or modifications to this equipment not specifically WARNING approved by the Xerox Corporation may void the user’s authority to operate this equipment. : In order to allow this equipment to operate in proximity to WARNING... - Page 9 Do not place the Xerox Nuvera Printer where people may step or trip on the power cord. Do not place objects on the power cord. Do not override or disable electrical or mechanical interlocks. Do not obstruct the ventilation openings. These openings prevent overheating of the machine.
-
Page 10: Laser Safety
This product contains laser-warning labels. These labels are intended for use by the Xerox Service Representative and are placed on or near panels or shields that require special tools for removal. Do not remove any of the panels. There are no operator serviceable areas in these covers. -
Page 11: Operational Safety
Operational Safety Your Xerox equipment and supplies were designed and tested to meet strict safety requirements. These include safety agency examination, approval, and compliance with established environmental standards. Your attention to the following safety guidelines will help ensure the continued safe operation of your Xerox Nuvera Printer: Use the materials and supplies specifically designed for your Xerox Nuvera Printer. -
Page 12: Consumable Information
Product Recycling & Equipment End of Life Disposal USA & Canada If you are managing the disposal of your Xerox product, please note that the product contains lamp(s) with mercury, and may contain lead, perchlorate, and other materials whose disposal may be regulated due to environmental considerations. - Page 13 In accordance with European legislation, end of life electrical and electronic equipment subject to disposal must be managed within agreed procedures. Prior to disposal, please contact your local dealer or Xerox representative for end of life take back information. Battery Statement...
- Page 14 Batteries should only be replaced by a MANUFACTURER approved service facility. Additional Information For more information on Environment, Health, and Safety in relation to this Xerox product and supplies, please contact the following customer help lines: USA: 1-800 828-6571 Canada:...
-
Page 15: Introduction
288 Perfecting System. About this Guide Read this guide before using the Xerox Nuvera EA Production System and Xerox Nuvera 288 Perfecting System. It will help you to become familiar with the system and your resources for maximizing system performance and productivity. -
Page 16: Xerox Nuvera Ea Production System
® Xerox Nuvera EA Production System Use the following diagram to become familiar with the basic components of a Xerox Nuvera EA Production System. Configurations vary according to modules installed on the system. DVD-RW Drive Control Console Optional Integrated Scanner... -
Page 17: Xerox Nuvera 288 Perfecting System
Xerox Nuvera 288 Perfecting System Use the following diagram to become familiar with basic components of a Xerox Nuvera 288 Perfecting System. Configurations vary according to modules installed on the system. DVD-RW Drive Optional Finisher Control Console One or Two Feed... -
Page 18: The Freeflow Print Server User Interface
Server User Interface The Xerox FreeFlow Print Server software provides a user interface (UI) to control all of the features and functions for your Xerox Nuvera printing system. The UI consists of windows, tabs, and dialogs that can be accessed through buttons and menus. -
Page 19: Menus
The status area of the UI, below the menu bar, displays information about the Print Server and provides buttons for some printer functions. Printer message field The printer message field at the top of the FreeFlow Print Server window displays status messages for the printer. Xerox Nuvera Getting Started Guide... - Page 20 Feature Access Buttons (FABs) enable you to set job properties. FABs are available from within specific tabs. Once property selections are made, your choices display on the FAB. • Tabs provide access to different information, settings, and FABs from within the same window. Xerox Nuvera Getting Started Guide...
-
Page 21: Your Learning Resources
CentreWare Network Print Drivers CD • User Guide and Training Aid (UGTA) CD Note: Some of the documents that ship with the Xerox Nuvera can also be found at www.xerox.com FreeFlow Print Server Help Select [Help] on the Xerox Nuvera EA Production System or Xerox Nuvera 288 Perfecting System user interface to open online Help. -
Page 22: Online Support Assistant
Online Support Assistant To use the Online Support Assistant, go to www.xerox.com/support, type “Nuvera” in the text box and select [Search]. Select the [Support] link for your Xerox Nuvera model. The Online Support Assistant provides the following types of information: •... -
Page 23: User Guide And Training Aid (Ugta)
Xerox Nuvera models problems, clear jams, and the modules that improve system can be configured on performance, and run systems. user diagnostics. Xerox Nuvera Getting Started Guide... -
Page 24: Additional Training
Additional training Additional training is available for your Xerox Nuvera EA Production System and Xerox Nuvera 288 Perfecting System. If you would like to receive optional on-site training, contact your Xerox representative for more information. Providing feedback Feedback from our customers is always appreciated. To provide... - Page 25 Xerox Nuvera Getting Started Guide...
- Page 26 Xerox Nuvera Getting Started Guide Xerox Nuvera Getting Started Guide...