Parts List; Dust Extraction - Clarke WOODWORKER CDS1 Operating & Maintenance Instructions

Parts List

I
tem Part No Description
1 GRCDS1001 Cable
2 GRCDS1002 Cable Support
3 GRCDS1003 Screw
4 GRCDS1004 Cable Grip
5 GRCDS1005 Brush Holder
6 GRCDS1006 Brush Lining
7 GRCDS1007 Spring
8 GRCDS1008 Carbon Brush
9 GRCDS1009 Governor
10 GRCDS1010 Switch
11 GRCDS1011 Pusher
12 GRCDS1012 Right Housing
13 GRCDS1013 Nameplate 1
14 GRCDS1014 Screw
15 GRCDS1015 Circuit Board
16 GRCDS1016 Stator
17 GRCDS1017 Bearing
18 GRCDS1018 Rotor
19 GRCDS1019 Bearing
20 GRCDS1020 Pin
21 GRCDS1021 Small Gear
22 GRCDS1022 Nut
Accessories
A wide range of accessories is available from your nearest CLARKE dealer, for further
information, contact your nearest dealer, or telephone CLARKE International Sales
department on 01992 565300.
PARTS & SERVICE TEL: 020 8988 7400
or e-mail as follows:
PARTS: Parts@clarkeinternational.com
SERVICE: Service@clarkeinternational.com
-7-
Qty Item Part No Description
23 GRCDS1023 Bearing
1
1 24 GRCDS1024 Large Gear
2 25 GRCDS1025 Output Shaft
1 26 GRCDS1026 Pin
2 27 GRCDS1027 Bearing
2 28 GRCDS1028 Back Support
2 29 GRCDS1029 Fore Support
2 30 GRCDS1030 Eccentric Wheel
1 31 GRCDS1031 Bearing
32 GRCDS1032 Bushing
1
2 33 GRCDS1033 Spring
1 34 GRCDS1034 Grinding Head
1 35 GRCDS1035 Screw
2 36 GRCDS1036 Grinding Plate
1 37 GRCDS1037 Gasket
1 38 GRCDS1038 Screw
1 39 GRCDS1039 Felt Layer
1 40 GRCDS1040 Screw
1 41 GRCDS1041 Sanding Paper
42 GRCDS1042 Screw
1
1 43 GRCDS1043 Nameplate 2
1 44 GRCDS1044 Left Housing
14. ALWAYS wear proper apparel. loose clothing or jewellery may
get caught in moving parts. wear protective hair covering to
contain long hair.
Qty
15. ALWAYS use recommended accessories. the use of improper
accessories could be hazardous.
1
16. ALWAYS remove plug from electrical outlet when adjusting,
changing parts, or working on the machine.
1
1
17. NEVER operate machine while under the influence of drugs, alcohol or any medication.
1
18. NEVER leave machine running unattended. turn power off. Do
1
not leave the machine until it comes to a complete stop.
1
19. NEVER force the machine. it will do a better and safer job at
1
the rate for which it was designed.
1
20. NEVER use power tools in damp or wet locations or expose
1
them to rain. Keep your work area well illuminated. do not use
1
in explosive atmosphere (around paint, flammable liquids etc.).
Avoid dangerous environment.
1
1
Additional Precautions For Power Tools
4
1
1. ALWAYS wear ear protectors/defenders as the noise level of this machine can exceed
1
85dB (A).
1
2. ALWAYS use the appropriate sanding pads for the work being done. Replacement
1
pads are available from your CLARKE dealer (see parts list for details).
3
3. ALWAYS keep the mains cable well away from the machine and ensure an adequate
1
electrical supply is close at hand so that the operation is not restricted by the length of
9
the cable.
1
4. ALWAYS switch the machine OFF immediately the task is completed.
1
5. NEVER allow the ventilation slots in the machine to become blocked.
6. DO NOT use the machine if the electric cable, plug or motor is in poor condition.
7. DONOT exert pressure on the sander to stop quickly, allow it to stop normally.
Additionally, please keep these instructions in a safe place for future reference.

DUST EXTRACTION

The sander is provided with a dust extraction facility, where a vacuum extractor, or dust
bag (not supplied), may be connected to the outlet at the rear of the machine. Please
note however, that this does not preclude the user from wearing a face mask to prevent
the inhalation of dust particles.
It is an EEC requirement that a dust extraction facility be provided on power tools, however,
due to the nature of the tool, some of the dust produced will be forced into the surrounding
atmosphere, and will not be collected.
-4-