Related Manuals for Clarke Woodworker CBS1-5B
Summary of Contents for Clarke Woodworker CBS1-5B
- Page 1 BELT/DISC SANDER MODEL NO: CBS1-5B PART NO: 6500432 OPERATION & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS LS0218 ISS 1...
-
Page 2: General Safety Rules
INTRODUCTION This CLARKE Belt and Disc Sander is for DIY and light workshop use for sanding wood and wood products. Read the manual and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. -
Page 3: Care Of Power Tools
5. KEEP other persons away. Do not let persons, especially children, not involved in the work, touch the tool or extension cable and keep them away from the work area. 6. Do not operate a machine when under the influence of alcohol, drugs or medication. -
Page 4: Dust Extraction
12. If the machine should be used outdoors, use only extension cables intended for outdoor use and marked accordingly. 13. Avoid accidental starting by making sure the power switch is off before plugging in the power cable. ADDITIONAL PRECAUTIONS FOR BELT & DISC SANDERS 1. -
Page 5: Electrical Connections
ELECTRICAL CONNECTIONS WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS FULLY BEFORE CONNECTING TO THE MAINS SUPPLY. Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This product is designed to operate on 230VAC 50Hz. -
Page 6: Sanding Belt Table
ASSEMBLY SANDING BELT TABLE 1. Slide the belt into the slot on the table. 2. Position the table so that the machined slot below lines up with the hole in the casting. 3. Use the handle and washer supplied to fix the table into position. -
Page 7: Sanding Disc Table
SANDING DISC TABLE 1. Line up the table pins with the L shape slots on either side of the sanding disc, push the table in as far as possible. 2. Screw the locking handwheels through the machined slots into the pre-drilled hole until finger tight. -
Page 8: Mitre Fence Adjustment
MITRE FENCE ADJUSTMENT 1. Check the mitre fence is perpendicular to the disc and adjust if required. 2. Set the pointer on the mitre fence to 0° if required • Once the pointer is set, you can adjust the angle to whatever angle you need. -
Page 9: Belt Tracking
BELT TRACKING 1. Remove the screws and clamping knob indicated. 2. Remove the belt cover. 3. Turn the belt by hand and adjust the tracking knob until the belt is tracking correctly. • Clockwise to track the belt to the right. •... -
Page 10: Operation
OPERATION IMPORTANT: Ensure that ALL components are secure, ALL correct adjustments have been carried out, and ALL safety precautions have been observed BEFORE plugging the machine into the mains supply and switching ON. 1. Attach a vacuum cleaner or other dust extraction device to the relevant extraction port. -
Page 11: Maintenance
MAINTENANCE Always inspect the sander before use. • Make sure that all air vents are clear. Check the power cable to ensure it is sound and free from damage. Avoid using solvents when cleaning plastic parts, (most plastics are susceptible to damage from the various types of commercial solvents). -
Page 12: Changing The Disc
CHANGING THE DISC 1. Remove the disc table and dust extraction moulding. 2. Using a sharp instrument, tease off a portion of the sanding disc, sufficient for it to be grasped by hand and peeled off. 3. Remove all residual adhesive and finally clean the disc with solvent. 4. -
Page 13: Specification
SPECIFICATION Model CBS1-5B Part Number 6500432 Electrical Supply 230V 50Hz 1 ph Fuse rating 5 Amp Power 250W Belt Size 25.4 x 762 mm Diameter of Disc 125 mm / 5 inch Table Size Belt Ø 148 mm Table Size Disc 184 x 98 mm Dust Extraction Outlet Inner diameter - 38mm / External diameter = 45mm... -
Page 14: Declaration Of Conformity
DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...