Related Manuals for Clarke CP150
Summary of Contents for Clarke CP150
- Page 1 150mm (6”) ORBITAL SANDER/POLISHER MODEL NO: CP150 PART NO: 6462101 OPERATION & MAINTENANCE INSTRUCTIONS GC0719- ISS 1 ORIGINAL INSTRUCTIONS...
-
Page 2: Environmental Recycling Policy
INTRODUCTION Thank you for purchasing this CLARKE Sander/Polisher. The random orbit dual action means you won't polish the same section continuously, but it will oscillate in random orbits reducing the risk of damage to your vehicle's paintwork. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. -
Page 3: General Power Tool Safety Warnings
GENERAL POWER TOOL SAFETY WARNINGS WARNING: READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS. FAILURE TO FOLLOW THE WARNINGS AND INSTRUCTIONS MAY RESULT IN ELECTRIC SHOCK, FIRE AND/OR SERIOUS INJURY. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated sander/ polisher. -
Page 4: Personal Safety
PERSONAL SAFETY 1. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. -
Page 5: Safety Symbols
Use of the power tool for operations different from those intended could result in a hazardous situation. SERVICE 1. Have your power tool serviced by a Clarke service centre using only identical replacement parts. This will ensure that the safety of the power tool is maintained. -
Page 6: Electrical Connections
ELECTRICAL CONNECTIONS WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS FULLY BEFORE CONNECTING THE MACHINE TO THE MAINS SUPPLY. This product is provided with a standard 13 amp, 230 volt (50Hz), BS 1363 plug, for connection to a standard, domestic electrical supply. Should the plug need changing, make sure that a plug of identical specification is used. - Page 7 OVERVIEW When unpacking, check for damage or shortages etc. Any found should be reported to your CLARKE dealer where the machine was originally purchased. NO DESCRIPTION NO DESCRIPTION ‘D’ Handle 14 mm Spanner Handle Fixing Bolts 6 mm Hexagon Key...
-
Page 8: Before Use
BEFORE USE WARNING: MAKE SURE THAT THE MACHINE IS SWITCHED OFF AND UNPLUGGED FROM THE MAINS SUPPLY BEFORE FITTING OR REMOVING THE ‘D’ HANDLE OR BACKING PAD. FITTING THE ‘D’ HANDLE 1. Fit the ‘D’ handle onto the body of the machine and secure with two allen screws supplied. -
Page 9: Starting The Machine
OPERATION Whether polishing or sanding, always make sure that any loose workpiece is securely fixed ie. clamped to a workbench or secured in a vice. • When working on car bodywork, the vibration may cause any items left on the car body to fall down. •... -
Page 10: Maintenance
3. All bearings etc, in this machine are lubricated with sufficient high grade lubricant for the machine’s lifetime under normal operating conditions, therefore no further lubrication is required. 4. Refer to your CLARKE dealer if internal maintenance is required. Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 11: Fault Finding
Remedy Tool will not No power supply. Check supply and operate. rectify as necessary. Faulty switch. Consult your Clarke dealer. Fuse blown. Replace fuse as on page Faulty motor. Consult your Clarke dealer. Motor runs but pad Drive gear broken. -
Page 12: Specifications
1.5 m/s Please note that the details and specifications contained herein, are correct at the time of going to print. However, CLARKE International reserve the right to change specifications at any time without prior notice. Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 13: Declaration Of Conformity
DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 14: Parts List And Diagram
PARTS LIST & DIAGRAM Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 15: Component Parts List
Bearing 627-2Z Screw M8x20 Draft shield Allen key CONSUMABLE ITEMS Replacement Foam Polishing Sponges, Polishing Bonnets and Sanding Discs (Grit 40, 60, 80) are available from your Clarke dealer. Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...