Specifications; General Information - Jøtul GF 400 DV IPI Sebago Installation And Operation Instructions Manual

139548-N GF 400 DV IPI 7/21
GF 400 DV IPI Sebago

Specifications

Input Rates
Natural Gas
32,000 BTU/hr. maximum input
17,000 BTU/hr. minimum input
Propane
30,000 BTU/hr. maximum input
14,000 BTU/hr. minimum input
Inlet Pressure:
Natural Gas: 5.0 WC (1.24 kPa)
Propane: 12.0 WC (2.90 kPa) 14.0 WC (3.48 kPa)
Manifold Pressure:
Natural Gas: 1.1 WC (.27 kPa)
Propane: 2.9 WC (.72 kPa)
• SIT Pro Flame 2 Intermitent Pilot Ignition - 120V / 60 Hz
• Steady State Efficiency: 76.60% NG / 77.02% LP
• AFUE Efficiency:
• CSA P4.1-15 Fireplace Efficiency:
NG - 67.70%
• Factory Air Shutter Settings: NG - 1/16" LP - 1/4"
• Continuous Pilot Ignition Mode ( CPI) may also be used
• Power Requirement: 120 VAC, 4 amps for
IFC Module, optional Blower and Accent Lamp.
Back-up Battery Pack: 4, AA - 1.5V
• Remote Control Transmitter batteries: 3, AAA - 1.5V
• Ambient Temperature Range: 32 -122°F (0 - 50°C)
• Remote Radio Frequency: 315 MHz
13"
330 mm
4
MIN MAX
7.0 WC (1.74 kPa)
MIN MAX
3.80 WC (.95 kPa)
11.0 WC (2.74 kPa)
69.27% NG / 69.45% LP
LP - 66.91%
26 1/2"
673 mm

General Information

THIS HEATER MUST BE INSTALLED AND MAINTAINED

BY A QUALIFIED SERVICE AGENCY.
The installation and repair of this appliance must be

done by a qualified service person. Failure to properly
install and maintain this heater could result in an
unsafe or hazardous installation, which may result in
a fire, explosion, property damage, personal injury or
loss of life.
This appliance should be inspected before use and

at least annually. More frequent cleaning may be
required due to excessive lint from carpeting, bedding
material, etc. It is imperative that control compart-
ments, burners, and circulating air passageways of
the appliance be kept clean. See Maintenance, page
26, for details.
THIS APPLIANCE MUST NOT BE CONNECTED TO A

CHIMNEY OR FLUE SERVING ANY OTHER APPLIANCE.
The installation must conform to local codes. Your lo-

cal Jøtul dealer can assist you in determining what is
required in your area for a safe and legal installation.
Some areas require a permit to install a gas burning
appliance. Always consult your local building inspec-
tor, or authority having jurisdiction, to determine
what regulations apply in your area.
CODE COMPLIANCE : Your local officials have final

authority in determining if a proposed installation is
acceptable. Any requirement that is requested by the
local authority having jurisdiction, that is not specifi-
cally addressed in this manual, defaults to local code.
In the absence of local codes, the installation re-
quirements must comply with the current edition of
National codes. In the U.S., these requirements are es-
tablished in the National Fuel Code, ANSI Z223.1.(NFPA
54) current edition. In Canada, the codes have been
established in CAN/CGA B149 Fuel Installation Code,
current edition..
Top Exit
29"
737 mm
178 mm
12 1/4"
311 mm
20 1/2"
521 mm
Safety Screen
Barrier
C L
7"
20 5/8"
524 mm
*For height with 6" Legs, subtract 2 1/4"
Rear Exit
C L
28 1/2"*
724 mm
25 1/2"*
647 mm