Interlogix Simon XT Installation Instructions Manual page 9

Alarm.com for use on the Image
Sensor Installer Test Site.
(www.alarm.com/imagesetup).
---Create Account This menu is available only to installers
who have their own Alarm.com
account creation system. You must
enter a Technician ID and a Lead ID in
order to use this menu.
System Programming + Scroll to Programming and enter the
Master Code Master Code.
- Interactive Services Select Interactive Services.
-- Module Status Provides status and troubleshooting
information for the GSM module.
-- Image Sensor This menu is used to view the status of
and test Image Sensors. This menu
can also be used to retrieve images
from the enrolled Image Sensors.
---Status View signal strength, PIR, battery and
other information about each Image
Sensor enrolled.
---Privacy Clear all Image Sensor images
currently stored on the XTi panel.
(This does not affect image storage on
the Alarm.com online account.)
---Image List View list of images captured by the
Image Sensor(s) on the system and
request to have specific images sent to
the panel for local viewing.
--- Test Put the Image Sensor in PIR Test
Mode (LED on sensor illuminates when
activated) or request an "Installer
Peek-In Now" to test image captures.
-- Weather Update Request a Weather Update if the
weather forecast is not showing on the
XTi touch screen. To speed up the
process, stay in Programming. This
keeps the panel in high-speed
communication mode with the touch
screens.
2
-- Z-Wave Used to add, remove, and troubleshoot
Z-Wave devices and networks. To
control Z-Wave devices via the
Alarm.com website and smart phone
apps, you will also need to enable Z-
Wave services on the account.
2 Add Z-Wave devices to the module's
--- Add Device
network. Make sure the device you
are trying to add is powered up and
within 3 to 6 feet of the Simon XTi
panel. Read the manufacturer's
instructions on what button to press on
the device to enroll it.
2
--- Remove Device Remove an existing Z-Wave device, or
to "reset" a Z-Wave device that was
previously learned into a different Z-
Wave network, before you can learn it
into the GSM module.
---Update 2WTTS Press Update 2WTTS to force an
update of the thermostat, lights or
locks information shown on the touch
Simon XT/XTi GSM Module V4 Installation Instructions
screen (2WTTS). Note that these
updates may take several minutes to
complete.
----Thermostats View thermostat data and
update/remove thermostats from
display on the panel and touch
screens.
----Lights Update the lights list shown on the
panel and touch screens.
----Locks Update locks list shown on panel and
touch screens and pair locks with their
door contact sensor.
--- Advanced Provides additional functionality for
advanced Z-Wave troubleshooting and
configuration.
---- Rediscovery Network rediscovery allows the system
to determine the most efficient
communication patch between Z-Wave
devices. (During this process the Z-
Wave network is busy and cannot
respond to other commands.)
---- Replicate Mode Initiates replicate mode on the panel.
---- Send Node Info For advanced use only. Do not use
unless directed to do so by Alarm.com.
---- Refresh Thermostat Requests updated thermostat data.
1
For use with Simon XTi only.
2 TM
Refer to the emPower installation instructions and guides on the
Alarm.com Dealer Site for more information on Z-Wave enrollment and
troubleshooting.
Walking customer through new user setup on the
web
This section describes how to help your customer set up their
website account, and only applies to customers on an
interactive service plan with an online account. (Skip this step
for customers using the module for wireless signaling only).
Before the customer can configure their website account, the
Alarm.com account for that customer must be created on the
Dealer Site, and the HSPA module associated with the account
must be installed successfully.
To log in and access their account, the customer can go to
www.alarm.com (or custom dealer website address) to
complete the new subscriber setup procedure.
The customer will need the following:
•
The website login and temporary password included on
the Alarm.com Welcome Letter generated when the
account was created by the Dealer
•
A list of their system sensors and touchpads with
corresponding zone IDs
•
At least one phone number and e-mail address where
notifications can be sent
9