Adding Vent Sections; Installing Natural Vent - Napoleon GDS50N Installation And Operating Instructions Manual

26

4.3.3 ADDING VENT SECTIONS

4.3.3 ADDING VENT SECTIONS
Add chimney sections, according to the manufacturers installation instructions. The chimney must extend at
Add chimney sections, according to the manufacturers installation instructions. The chimney must extend at
least, 3 feet (1m) above its point of contact with the roof and at least 24 inches (61cm) higher than any wall,
EN least, 3 feet (1m) above its point of contact with the roof and at least 2 feet (0.6m) higher than any wall, roof,
roof, building or obstacle within 10 feet (3m) horizontally.
building or obstacle within 10 feet (3m) horizontally.
3 FT
3 FT
(1m)
(1m)
MIN
MIN

4.3.4 INSTALLING NATURAL VENT

4.3.4 INSTALLING NATURAL VENT
ADAPTER INSTALLATION: ADAPTER INSTALLATION:
• • Remove the spill switch bracket from the rear of the Remove the spill switch bracket from the rear of the
adapter.
adapter.
• • Gently pull the two wire terminals (located inside the Gently pull the two wire terminals (located inside the
7" (178mm) ue collar at the top of the appliance) out 7" (178mm) flue collar at the top of the appliance) out
approximately 8" (203mm).
approximately 8" (203mm).
• • Bring the wires through the lower hole in the adapter and Bring the wires through the lower hole in the adapter
out the spill switch opening. To pass the wires through
and out the spill switch opening. To pass the wires
the hole more easily, temporarily take the two terminals through the hole more easily, temporarily take the two
together.
terminals together.
• • With the spill switch opening aligned to the back of the With the spill switch opening aligned to the back of the
appliance, take hold of the adaptor base and push the
appliance, take hold of the adaptor base and push the
crimped edge into the appliance  ue collar. crimped edge into the appliance flue collar.
• Connect the wire terminals to the spill switch and re secure
• Connect the wire terminals to the spill switch and
the bracket. resecure the bracket.
For aesthetics, the adaptor has been designed to accept a standard For aesthetics, the adaptor has been designed to accept
matte black 7" (178mm) appliance pipe and a decorative black
a standard matte black 7" (178mm) appliance pipe and a
band (standard with the GS150KT). Both are available from your decorative black band (standard with the GS150KT). Both are
local authorized dealer / distributor.
available from your local authorized dealer / distributor.
W415-1427 / 12.23.14
24" (61cm) MIN
2 FT (0.6m) MIN
10 FT (3m)
10 FT (3m)
TO NEAREST
TO NEAREST
ROOFLINE
ROOFLINE
10 FT (3m)
10 FT (3m)
OR MORE
OR MORE
FLAT ROOF
FLAT ROOF
REV B : Added metric dimensions
LESS THAN
LESS THAN
10 FEET
10 FEET
(3m)
(3m)
24" (61cm)
2 FT (0.6m)
RIDGE
RIDGE
MIN
MIN
3 FT (1m)
3 FT (1m)
3 FT (1m)
MIN
3 FT (1m)
MIN
MIN
MIN
3 FT (1m)
3 FT (1m)
MIN
MIN
LESS THAN
LESS THAN
10 FEET
10 FEET
(3m)
(3m)
24" (61cm)
2 FT (0.6m)
MIN
MIN
WALL
WALL
59.1B
ADAPTER
SPILL
SWITCH
W415-1427 / B / 08.01.18
27
EN