Related Manuals for Fisher & Paykel DCS GDSBE1-30
Summary of Contents for Fisher & Paykel DCS GDSBE1-30
- Page 1 DOUBLE SIDE BURNER/GRIDDLE GDSBE1-30 Models INSTALLATION GUIDE US CA 592076A 11.19...
-
Page 2: Safety And Warnings
SAFETY AND WARNINGS WARNING! Electric Shock Hazard Failure to follow this advice may result in electric shock or death. • This appliance is equipped with a three-prong or four-prong grounding plug for your protection against shock hazard and should be plugged DANGER directly into a properly grounded power outlet. - Page 3 SAFETY AND WARNINGS WARNING! WARNING! Hot Surface Hazard Explosion Hazard Failure to follow this advice may result in fire, Failure to follow this advice may result in burns, scalds or personal injury. injury or death • Accessible parts may become hot during use. •...
- Page 4 SAFETY AND WARNINGS Do not store a full LP tank in direct sunlight. Gas requirements After a period of storage or non-use, the appliance should be checked for gas leaks, This appliance can be used with any brand of 20lb LP gas tank provided it is compatible deterioration, proper assembly, and burner obstructions before use.
-
Page 5: Product Dimensions
PRODUCT DIMENSIONS FRONT PROFILE GDSBE1-30 MODELS PRODUCT DIMENSIONS INCHES A Overall height (excluding burners and pan supports) 10 1/2 B Overall width C Overall depth (excluding dials) 26 7/8 D Depth of chassis 22 5/8 E Width of chassis (including support brackets) 27 13/16 F Height below countertop 9 15/16... -
Page 6: Cutout Dimensions
CUTOUT DIMENSIONS STANDARD CUTOUT INSULATED JACKET CUTOUT If the unit is to be placed into a combustible enclosure, an insulated jacket is required. ventilation ventilation GDSBE1-30 MODELS GDSBE1-30 MODELS CUTOUT DIMENSIONS CUTOUT DIMENSIONS INCHES INCHES A Height of cutout 10 1/8 A Height of cutout 11 1/8 B Depth of cutout... - Page 7 CLEARANCES Clearances to non-combustible construction Material which is not capable of being ignited and burned, such as materials consisting entirely of, or a combination of, steel, iron, brick tile, concrete, slate, and plaster. The side burner/griddle is designed for easy placement into built- in masonry enclosures.
- Page 8 CLEARANCES Clearances to combustible construction Any materials of a building structure or decorative structure made of wood, compressed paper, plant fibres, vinyl/plastic or other materials that are capable of transferring heat or being ignited and burned. Such material shall be considered combustible even though flame-proofed, fire-retardant treated or surface-painted, or plastered.
-
Page 9: Electrical Connection
ELECTRICAL CONNECTION All units are supplied with a 12V power transformer to operate the products ignition and dial illumination features. The transformer is sealed in a box with an attached power supply cord. Electrical requirements Use only a Ground Fault Interrupter (GFI) protected circuit with this product. -
Page 10: Gas Connection
GAS CONNECTION GAS REQUIREMENTS NATURAL GAS CONNECTION Verify the type of gas supply to be used, either natural or LP, and make sure the marking Connection: 1/2” NPT male with 3/8” flare adapter Operating pressure: 4.0” W.C. on the appliance rating plate agrees with that of the supply. The rating plate is located on Supply pressure: 5”... - Page 11 GAS CONNECTION CART LP CONNECTION BUILT-IN LP CONNECTION If the double side burner/griddle is to be installed in a built-in application, then the side Units set for use with LP gas come equipped with a high capacity hose/regulator assembly burner/griddle must be installed in accordance with the built–in installation guidelines and for connection to a standard 20 lb.
-
Page 12: Leak Testing
LEAK TESTING A complete gas tightness check must be performed at the installation site. Periodically check Testing for leaks the whole system for leaks, or immediately if the smell of gas is present. Removing the valve panel Prepare soap solution by combining one part liquid detergent and one part water. -
Page 13: Low Flame Adjustment
LOW FLAME ADJUSTMENT The valves on the double side burner/griddle unit feature an adjustable low setting. Due to fluctuations in gas pressure, or heating value you may feel it necessary to increase or decrease gas flow in the low position. If the gas type has been converted from natural to LP or vice-versa, the low flame setting must be reviewed and adjusted. Push in and hold the selected dial for two seconds before turning to Remove the dial. - Page 14 FREESTANDING CART INSTALLATION (OPTIONAL) Designed with flexibility in mind, the 30” double side burner/griddle can be either built-in Securing side burner/griddle to cart or mounted on a freestanding cart. If the unit is to be placed onto a freestanding cart, an approved DCS cart is required and can be purchased separately from your local DCS dealer.
-
Page 15: Installer Checklist
INSTALLER CHECKLIST IMPORTANT! Read all installation instructions in this manual to see if the unit has been correctly installed. Ensure that installation has been completed correctly before use. Ensure that: specified clearances are maintained to combustibles flame has been adjusted proper enclosure ventilation has been verified each burner lights satisfactorily - individually or with adjacent burner lit all internal packaging and any adhesive residue is removed... - Page 16 DCSAPPLIANCES.COM © Fisher & Paykel Appliances 2019. All rights reserved. The product specifications in this document apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time.