User- Selectable Fea Tures - Clifford Tazor 4 Owner's Manual

Dei clifford tazor 4 car alarms: user guide

Installation manual (27 pages)

Table of Contents

If you opted to have the Clifford DataPort interface connector installed with your system, you can use our CliffNet Wizard software to access your system

through your Windows PC. CliffNet Wizard will show you, on your PC screen, all your user-programmable feature settings. You can change settings

simply by mouse-clicking the graphical button for each feature. You can customize features, add or delete remote controls, change remote control button

assignments, view a chronological history of trigger and sensor activations, and much more. It's actually fun! And secure. To learn more and download

this free software, go to www.clifford.com/wizard.

You may set many of the features to your own preferences. Once you've changed a few settings, you'll find that programming the system is so easy that

you can even do it while driving. The system comes with all of its features preprogrammed as noted by the bold type in the Table of user-selectable features. To

change any of the settings, use the steps noted below. To restore the feature to its factory setting, just repeat the procedure.

NOTE: For greater programming ease and even more system control, consider the CliffNet Wizard Windows PC

software interface: www.clifford.com/wizard.

How to change a user- selectable fea ture:

Briefly, here's how it will work:

You will pick a feature from the following Table of User-Selectable Features, noting the feature's column and row numbers.

You'll enter program mode by entering your valet code and pressing the

switch until you hear a chirp.

Press the blank PlainView 2 switch button the same number of times as the column number, then the

times equal to the row number.

1. Refer to the Table of user-selectable features and make note of the column (across) number and the row (down) number of the feature(s) you wish to

program.

2. Turn the ignition on, or start the engine (skip this step if the engine is running).

3. Enter your valet code, then press and hold the

4. Select the feature column: Press and release the blank button of the PlainView 2 switch the same number of times as the column number you wish.

Pause. You will hear the same number of chirps as the column number, audibly confirming your selection.

5. Select the feature row: Press and release the

you count.

NOTE: You have 5 sec onds to en ter the row number af ter se lect ing the col umn number. If you wait too long, the sys tem

jumps back to the "Fea ture Se lect" po si tion (this is in di cated with 3 chirps). If you wait an other 60 sec onds, the sys tem

will exit pro gram mode.

6. Pause. You will hear either one or two chirps: Two chirps = ON, one chirp = OFF (If there is a NOTE for the selected feature, perform the actions

noted).

NOTE: Some fea tures, such as AutoStart (col umn 2, row 4) used with the optional IntelliStart 4 accessory, have

mul ti ple set tings. Sim ply re se lect the fea ture ad di tional times to prog ress through each pos si ble set ting.

7. You may now select another feature or exit program mode:

a. To select another feature in that same column, repeat step 5 within the next 5 seconds (after 5 seconds, 3 chirps mean you are back to the

"Feature Select" position).

b. To select a different feature column, go to step 4.

c. To exit program mode, turn the ignition off (you'll hear 3 chirps and the LED will turn off). If driving, just wait 60 seconds and the system

will automatically exit program mode.

If you make an er ror, just turn off the ig ni tion and start again.

EX AM PLE: Turn on Lock upon AutoArming and turn off Re mote Valet Mode and FACT:

In this example, we'll change three different features in just one programming session: We'll turn on the Lock upon AutoArming feature, turn off remote

controlled valet mode and turn off the FACT anti-falsing feature:

1. Enter program mode as previously noted (ignition on, enter your valet code, press and hold the

you hear a chirp).

2. Since the Lock upon AutoArming feature is in column 3, row 2 of the Table, go to column 3 by pressing the blank button on the PlainView 2

switch three times. Wait for the 3-chirp/column 3 confirmation. Then press the

button). After a brief pause, you'll hear 2 chirps to confirm that Lock upon AutoArming is now on.

3. Since FACT is also in column 3, there is no need to reselect column 3. Therefore, you can go straight to the row selection. Select row 4 by

pressing the

button four times. After a brief pause, you'll hear one chirp to confirm that FACT is now off.

4. You'll note that the Remote valet mode feature is at column 2, row 3. To change to column 2, press the blank button twice, then wait for the

2-chirp/column 2 confirmation. Press the

Remote valet mode feature is now turned off.

5. To exit the program mode, turn the ignition off. You'll hear 3 chirps to confirm program mode exit.