Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Clifford AvantGuard II
Summary of Contents for Clifford AvantGuard II
- Page 1 World-Class Auto Security AvantGuard Owner's Manual...
-
Page 3: Table Of Contents
Remote Starter Do’s and Don’ts ......10 How to Program Your AvantGuard II ......11 How to Change Siren Duration . -
Page 4: Extremely Important Notice
EXTREMELY IMPORTANT NOTICE If the AvantGuard II’s control unit is removed from the vehicle for any reason, the supplied RED jumper wire MUST BE CONNECTED to pins #8 and #11 of the PIGTAIL connector. 1. The AvantGuard II is designed to be used only on a gasoline-powered, fuel-injected vehicle with automatic transmission. -
Page 5: How To Operate The Premier™ Remote Control
What’s more, the remote control’s four buttons and eight different channels enables you to remotely command any aspect of the AvantGuard II and its optional accesso- ries. It is also capable of controlling AvantGuard II, IntelliGuard Series and Clifford Nova, Delta IV and Ace II systems and accessories on other vehicles you own —... -
Page 6: How To Arm The System With The Remote Control
3. Release button I as soon as you observe any of the above actions. How to Panic the System As an added safety measure, AvantGuard II is designed to respond if you ever face harassment and are within transmittal range of the vehicle. Simply press button I continuously for 3 seconds. -
Page 7: Valet Mode
Valet Mode Whenever your vehicle is to be serviced, washed or valet parked, you must use the valet mode to disarm the system and override its Smart AutoArming feature. How to Enable Valet Mode 1. Insert your key and turn the ignition to the “ON” position. 2. -
Page 8: Smart Autoarming
(see page 5) or leave one of the doors open. Smart AutoDiagnostics™ The AvantGuard II will automatically and instantly perform a comprehensive test of all system triggers and sensors every time you arm the system. In the rare event... -
Page 9: Prior Intrusion Attempt Alert
Prior Intrusion Attempt Alert If the alarm sounded while you were away, when you remotely disarm the system will issue three chirps and three flashes of the parking lights. You’ll note that the Multicolor LED will blink in red 1-7 times, pause for one second then repeat the cycle four more time. -
Page 10: Smartsiren
b. To turn the chirps on: Flick the switch to its latched position, then back to center. c. You will hear 3 chirps to confirm chirp muting or restoration. 7. Turn the ignition off. You will hear 3 chirps to confirm exiting of program mode. One-Cycle Chirp Muting: This is particularly useful when parking in a quiet residential area. -
Page 11: Remote Engine Starting
2. Press the brake pedal and/or shift the transmission out of “PARK.” 3. The AvantGuard II is now disengaged and your vehicle will operate as usual. NOTE: For security reasons, if you press the brake pedal or shift the trans- mission out of “PARK”... -
Page 12: How To Engage Autostart
How to Engage AutoStart 1. Make sure that the gas tank is at least half full. To conserve battery power, make sure the air conditioner, radio and all other accessories are turned off. 2. Insert your ignition key and turn the switch to the “ON” position. 3. -
Page 13: How To Program Your Avantguard Ii
Clifford Electronics factory. If, however, you would like to set your AvantGuard II to meet you own specific needs and preferences, doing so is as simple as a few flicks of a switch. -
Page 14: How To Set Your Own Personalized Siren Sound
How to Set Your Own Personalized Siren Sound You can program a unique code of siren chirps to recognize your system at a distance.. Your Personalized Siren Sound will consist of any combination of eight or less dot (short) and/or dash (long) siren pulsating sounds. A dot is a 1/4-second siren chirp. A dash is a 3/4-second chirp. -
Page 15: How To Adjust Sensitivity Of The Optional Omnisensor
How to Adjust Sensitivity of the Optional OmniSensor You can easily increase or decrease the sensitivity of the optional OmniSensor any time, any place, without tools and without even knowing where to sensor is mounted. To change sensitivity of the optional OmniSensor, use the following procedure: 1. -
Page 16: How To Enable/Disable Autolock And Autounlock
How to Enable/Disable AutoLock and AutoUnLock The system automatically locks your car doors 5 seconds after you shift the trans- mission into Drive. Conversely, the doors automatically unlock after you turn the ignition off. To disable or re-enable this feature, use the following procedure: 1. -
Page 17: How To Set The Smart Autoarming Entry Delay
How to Add a New Remote Control Your AvantGuard II can function with as many as eight differently coded remote controls. To add any type of Clifford remote control, use the following procedure: 1. Turn ignition to the ON position. -
Page 18: How To Delete The Code Of A Lost Or Stolen Remote Control
b. Flip the switch to its latched position, then back to center. You will hear 3 chirps. c. Tap the switch to its momentary position 1 time. d. Flip the switch to its latched position, then back to center. You will hear 1 chirp. -
Page 19: Quick Programming Guide
Quick Programming Guide Once you are familiar with the AvantGuard II programming procedures, you may use this quick guide to make programming changes. IMPORTANT: DO NOT use this guide unless you have programmed the AvantGuard II before. If you have never programmed the system before, you should refer first to the detailed programming instructions in the appropriate section of How To Program Your AvantGuard II. - Page 20 Programmable Parameter Feature Any pattern Personalized of up to 8 dots Siren Sound and/or dashes From 1 second Siren duration to 5 minutes Optional Sensor Sensitivity OmniSensor Channel 1 (arm/disarm) Channel 2 (accessory) Add a new remote control Channel 3 (accessory) Channel 4 (accessory)
- Page 21 AutoStart is engaged (e.g., the transmission is not in the Park position. All Clifford automotive security systems are designed, developed and manufactured in the USA to the most rigorous standards © Copyright Clifford Electronics, Inc., 1992 70-243C/80-1212/AG2OM Step Number Action...