Ordering Spare Parts; Maintenance And Repairs - Stihl MS 201 TC-M Instruction Manual

30 Ordering Spare Parts

29.6 Cutting Attachment
Actual cutting length may be less than the speci‐
fied length
29.6.1 Rollomatic guide bars
Bar lengths (3/8" P pitch):
Groove width:
29.6.2 3/8" Picco chains
Picco Micro 3 (63 PM3) Type 3636
Pitch:
Drive link gauge:
Picco Super 3 (63 PS3) Type 3616
Pitch:
Drive link gauge:
Picco Duro 3 (63 PD3) Type 3612
Pitch:
Drive link gauge:
29.6.3 Chain Sprockets
6-tooth for 3/8" P (spur sprocket)
Max. chain speed according to
ISO 11681:
Chain speed at maximum power: 18.6 m/s
29.7 Sound and Vibration Levels
For further details concerning compliance with
the Employers' Directive on Vibration
2002/44/EC, see www.stihl.com/vib
29.7.1 Sound pressure level L
ISO 22868
100 dB(A)
29.7.2 Sound power level L
113 dB(A)
29.7.3 Vibration level a
MS 201 TC-M with
3/8" P chain:
The K‑factor in accordance with Directive
2006/42/EC is 2.0 dB(A) for the sound pressure
level and sound power level; the K‑factor in
accordance with Directive 2006/42/EC is
2
2.0 m/s for the vibration level.
29.8 REACH
REACH is an EC regulation and stands for the
Registration, Evaluation, Authorisation and
Restriction of Chemical substances.
For information on compliance with the REACH
regulation (EC) No. 1907/2006 see
www.stihl.com/reach.
0458-599-0121-C
30, 35, 40 cm
1.3 mm
3/8" P (9.32 mm)
1.3 mm
3/8" P (9.32 mm)
1.3 mm
3/8" P (9.32 mm)
1.3 mm
26.0 m/s
to
peq
to ISO 22868
weq
to ISO 22867
hv,eq
Handle, left Handle,
right
2 2
3.5 m/s 3.1 m/s
29.9 Exhaust Emissions
The CO value measured in the EU type approval
2
procedure is specified at www.stihl.com/co2.
The measured CO value was determined on a
2
representative engine in accordance with a
standardized test procedure under laboratory
conditions and does not represent either an
explicit or implied guarantee of the performance
of a specific engine.
The applicable exhaust emission requirements
are fulfilled by the intended usage and mainte‐
nance described in this instruction manual. The
type approval expires if the engine is modified in
any way.
30 Ordering Spare Parts
Please enter your saw model, serial number as
well as the part numbers of the guide bar and
saw chain in the spaces provided. This will make
re-ordering simpler.
The guide bar and saw chain are subject to nor‐
mal wear and tear. When purchasing these
parts, always quote the saw model, the part
numbers and names of the parts.
Model
Serial number
Guide bar part number
Chain part number

31 Maintenance and Repairs

Users of this machine may only carry out the
maintenance and service work described in this
user manual. All other repairs must be carried
out by a servicing dealer.
STIHL recommends that you have servicing and
repair work carried out exclusively by an author‐
ized STIHL servicing dealer. STIHL dealers are
regularly given the opportunity to attend training
courses and are supplied with the necessary
technical information.
When repairing the machine, only use replace‐
ment parts which have been approved by STIHL
for this power tool or are technically identical.
Only use high-quality replacement parts in order
to avoid the risk of accidents and damage to the
machine.
English
31