Download Print this page
Stihl MS 200 T Instruction Manual

Stihl MS 200 T Instruction Manual

Hide thumbs Also See for MS 200 T:

Advertisement

Quick Links

{
STIHL MS 200 T
Instruction Manual
Manual de instrucciones
Warning!
To reduce the risk of kickback injury use
STIHL reduced kickback bar and STIHL PMC3
(3/8" Picco) chain depending on sprocket pitch
or other available low kickback components.
Advertencia!
Para reducir el riesgo de lesionarse como
resultado de un culatazo, utilice la barra de
contragolpe reducido y la cadena PMC3
(Picco de 3/8 pulg) de STIHL, dependiendo de
la rueda dentada usada y de otros
componentes reductores de contragolpe.
Read and follow all safety precautions in
Instruction Manual – improper use can cause
serious or fatal injury.
Lea y siga todas las precauciones de
seguridad dadas en el manual de
instrucciones – el uso incorrecto puede causar
lesiones graves o mortales.

Advertisement

loading

Summary of Contents for Stihl MS 200 T

  • Page 1 Para reducir el riesgo de lesionarse como resultado de un culatazo, utilice la barra de contragolpe reducido y la cadena PMC3 (Picco de 3/8 pulg) de STIHL, dependiendo de la rueda dentada usada y de otros componentes reductores de contragolpe.
  • Page 2 Instruction Manual 1 - 53 Manual de instrucciones 55 - 112...
  • Page 3 For further information you Operating Instructions can go to www.stihlusa.com. Oil Quantity Control Contact your STIHL dealer or the STIHL Taking Care of the Guide Bar distributor for your area if you do not Cleaning the Air Filter...
  • Page 4 Engineering Improvements Fuel tank; fuel mixture of Symbols in Text gasoline and engine oil STIHL’s philosophy is to continually improve all of its products. As a result, Many operating and safety instructions Chain oil tank; chain oil engineering changes and improvements are supported by illustrations.
  • Page 5 Most of these safety precautions and trained in special the safety instructions warnings apply to the use of all STIHL cutting and work- periodically. Careless or chain saws. Different models may have ing techniques and improper use may cause different parts and controls.
  • Page 6 In order to reduce the risk of whitefinger disease and carpal tunnel Warning! syndrome, please note the following: The ignition system of the STIHL unit Physical Condition – Most STIHL power tools are produces an electromagnetic field of a...
  • Page 7 Accidental accel- your ability to hear warnings (shouts, Your STIHL power tool uses an oil- eration of the engine can cause the alarms, etc.) is restricted. gasoline mixture for fuel (see chapter on chain to rotate.
  • Page 8 Select bare ground for fueling and move To do this with this STIHL cap, raise the at least 10 feet (3 m) from the fueling grip on the top of the cap until it is upright spot before starting the engine.
  • Page 9 Chain" of your instruction manual. spill quantities of fuel. In STIHL Oilomatic chain, guide bar and Starting order to reduce the risk sprocket must match each other in of fuel spillage and fire, tighten the fuel gauge and pitch.
  • Page 10 If you cannot set the correct idle speed, (see section on reactive forces). To Warning! have your STIHL dealer check your reduce this risk, always engage the Do not drop start. This method is very power tool and make proper chain brake before starting.
  • Page 11 The pressure limbs or branches. may cause the bar and rotating chain to pop out of the cut or kerf, go out of control and strike the operator or some MS 200 T...
  • Page 12 When it cutting. is not in use (e. g. during a work break), shut it off and make sure that unauthor- ized persons do not use it. MS 200 T...
  • Page 13 STIHL servicing dealer. Warning! the chain brake is engaged. It can result If this tool is subjected to unusually high...
  • Page 14 You may also permanently when the moving saw to kickback. damage the engine. Have your muffler chain near the upper serviced and repaired by your STIHL quadrant of the bar nose servicing dealer only. contacts a solid object or Warning! is pinched.
  • Page 15 Some of ANSI B 175.1-2000 may bear no rela- kickback bars and low kickback chains. STIHL bar and chain types are designed tionship to actual kickback bar rotation to reduce kickback forces. STIHL angles that may occur in real life cutting recommends the use of reduced situations.
  • Page 16 (see above at "Important All STIHL chain saws are equipped with tact with the operator. Adjustments"). a Quickstop chain brake which can be Low Kickback Saw Chain and activated by inertia.
  • Page 17 Do not mount a bow guide on any STIHL dealer for such combinations. been specifically certified to comply with STIHL chain saw. Any chain saw the 45° computer derived kickback equipped with a bow guide is potentially angle of § 5.11 of ANSI B 175.1-2000.
  • Page 18 STIHL Chain Saw Safety may cause loss of saw control. lose control. Manual, which is available free from Pushback frequently occurs when the your STIHL servicing dealer.
  • Page 19 Have such work per- operator and cause loss of control of the formed by your STIHL servicing dealer saw and severe or fatal injury to the only. For example, if improper tools are operator.
  • Page 20 Do not operate your chain saw if the grease and other foreign matter which STIHL is the only manufacturer in the muffler is damaged, missing or modi- may reduce friction of the band on the industry to produce its own chain saws, fied.