Gigaset A120 Manual page 12

Appendix
Entering letters/characters
Standard
1x 2x 3x 4x 5x 6x 7x 8x 9x 10x 11x 12x 13x 14x 15x
characters 1
1
2
Press the relevant key
a
I
the number of times
d
4
indicated.
g
5
Briefly press the hash
j
#
L
key to switch from
m n
M
"Abc" to "123" mode,
p
N
from "123" to "abc"
t
O
mode and from "abc"
w x
Q
to "Abc" mode.
P
*
#
1) Space
Specifications
Batteries
Technology: Nickel-metal-hydride (NiMH); Size: AAA (Micro, HR03); Voltage: 1.2 V;
Capacity: 400 - 1000 mAh
General specifications
DECT standard
GAP standard
Range
Base station power supply
Radio frequency range
Transmission power
Environmental conditions
in operation
Base station power consumption
In standby mode
– Handset in base station
– Handset outside base station
During a call
£ $ ¥ ¤
b c 2 ä á à â ã ç
e f 3 ë é è ê
h i 4 ï í ì î
k l 5
o 6 ö ñ ó ò ô õ
q r s 7 ß
u v 8 ü ú ù û
y z 9 ÿ ý æ ø å
1)
. , ? ! 0 + - : ¿
/ ( ) < = > %
# @ \ & §
is supported
is supported
up to 300 m outdoors, up to 50 m indoors
230 V ~/50 Hz
1880-1900 MHz
10 mW average power per channel, 250 mW
pulse power
+5 °C to +45 °C, 20% to 75% relative humidity
A120/A220 A120A
ca. 1.0 W ca. 1.2 W
ca. 0.8 W ca. 1.0 W
ca. 1.0 W ca. 1.2 W
12
Questions and answers
If you have any queries about the use of your telephone, visit our website at
www.gigaset.com/service for 24-hour support. The table below contains a list of com-
mon problems and possible solutions.
Problem
Nothing
appears in
the display.
No wireless
connection
to the base
station,
Base flashes in
¡ " ' ; _ the display.
You cannot
hear a ringer/
dialling tone
from the fixed
line network.
Error tone
sounds after
system PIN
prompt.
PIN forgotten.
Contact with liquid
If the handset has come into contact with liquid:
1 Switch off the handset and remove the battery pack immediately.
2 Allow the liquid to drain from the handset.
3 Pat all parts dry, then place the handset with the battery compartment open and
the keypad facing down in a dry, warm place for at least 72 hours (not in a micro-
wave, oven etc.).
4 Do not switch on the handset again until it is completely dry.
When it has fully dried out, you will normally be able to use it again.
Cause Solution
The handset is not switched Press the end call key
on. 5 seconds or place the handset in
the base station.
The batteries are flat. Charge or replace the batteries.
The handset is outside the Move the handset closer to the base
range of the base station. station.
The handset is not regis- Register the handset
tered.
The base station is not Check the mains connector on the
turned on. base station
The phone cord supplied Please always use the phone cord
has not been used or has supplied or ensure that the
been replaced by a new cord pin connections are correct when
with the wrong jack connec- purchasing from a retailer: 3-4
tions. assignment of telephone leads/
EURO CTR37.
The system PIN you have Reset the system PIN to the default
entered is incorrect. 0000
All handsets are de-registered. All
settings are reset. All lists are
deleted.
!
a
for approx.
¢
page 9.
¢
page 3.
¢
page 11.