Panasonic KX-FC971CX-S Service Manual page 48

KX-FC971CX-S / KX-FGA521CX-S
7.3.3. SERVICE FUNCTION TABLE
Code
501 Pause time
502 Flash time
511 VOX sense
514 Bell detection time
520 CED frequency select
521 International mode select
522 Auto standby select
523 Receive equalizer select
524 Transmission equalizer select
544 Document feed position adjustment
value set
550 MEMORY CLEAR
551 ROM check
553 Monitor on FAX communication select 1:OFF
554 Modem test
555 Scan check
556 Motor test
557 LED test
558 LCD test
559 Document jam detection select
561 KEY test
562 Cutter test
570 BREAK % select
571 ITS auto redial time set
572 ITS auto redial line disconnection time
set
573 Remote turn-on ring number set
590 FAX auto redial time set
591 FAX auto redial time disconnection
time set
592 CNG transmit select
593 Time between CED and 300bps
594 Overseas DIS detection select
Function Set Value
1:SHORT (3S)
2:LONG (5S)
1:Type1
2:Type2
3:Type3
1:High 2:Low
X 10 msec
1:2100 Hz
2:1100 Hz
1:ON 2:OFF
1:ON 2:OFF
1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km
1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km
1: 3 mm
2: 4 mm
3: 5 mm
4: 6 mm
5: 7 mm
2:PHASE B
3:ALL
1:ON 2:OFF
1:61% 2:67%
X number of
times
X second
X number of
rings
X number of
times
X second
1:OFF
2:ALL
3:AUTO
1:75 msec
2:500 msec
3:1 sec
1:detects at
the 1st time
2:detects at
the 2nd time
Effective Default
Range
1, 2 1
1, 2, 3 2 1: 100 ms 2: 600 ms 3: 300 ms
1, 2 1 When the TAM (or EXT TAM) does not stop recording
the ICM because noise is detected on the telephone
line, change this setting to "LOW".
10~90 60
1, 2 1 See Symptom/Countermeasure Table for long
distance and international calls in The unit can copy,
but cannot transmit/receive (P.74).
1, 2 1 See Symptom/Countermeasure Table for long
distance and international calls in The unit can copy,
but cannot transmit/receive (P.74).
1, 2 1 The resolution reverts to the default when
transmission is complete.
1~4 1 When the telephone station is far from the unit or
reception cannot be performed correctly, adjust
accordingly.
1~4 1 When the telephone station is far from the unit or
transmission cannot be performed correctly, adjust
accordingly.
1~5 3 If it is difficult to feed documents, raise the set value.
If multi documents feed occurs, lower the set value.
See Memory Clear Specification(P.49).
See TEST FUNCTIONS(P.50).
1~3 1 Sets whether to monitor the line signal with the unit´s
speaker during FAX communication or not.
See TEST FUNCTIONS(P.50).
See TEST FUNCTIONS(P.50).
0 See TEST FUNCTIONS(P.50).
See TEST FUNCTIONS(P.50).
See TEST FUNCTIONS(P.50).
1, 2 1 See TEST FUNCTIONS(P.50).
See TEST FUNCTIONS(P.50).
Press "SET" key.
1, 2 1 Sets the % break of pulse dialing according PBX.
00~99 05 Selects the number of times that ITS is redialed (not
including the first dial).
001~255 065 Sets the interval of ITS redialing.
01~99 10 Sets the number of rings before the unit starts to
receive a document in the TEL mode.
00~99 05 Selects the number of redial times during FAX
communication (not including the first dial).
001~999 065 Sets the FAX redial interval during FAX
communication.
1~3 2 Lets you select the CNG output during FAX
transmission. ALL: CNG is output at phase A. AUTO:
CNG id output only when automatic dialing is
performed. OFF: CNG id not output at phase A. Refer
to Sometime there is a transmit problem(P.72).
1~3 1 See Symptom/Countermeasure Table for long
distance and international calls in The unit can copy,
but cannot transmit/receive (P.74). Refer to
Receive Problem(P.73) and The unit can copy, but
cannot transmit/receive (P.74).
1, 2 1 See Symptom/Countermeasure Table for long
distance and international calls in The unit can copy,
but cannot transmit/receive (P.74). Refer to
Sometime there is a transmit problem(P.72) and
The unit can copy, but cannot transmit/receive
(P.74).
48
Remarks
----------
----------