Husqvarna Automower 405X Operator's Manual page 30

• Get extended product information.
• Get an alarm if the product moves out of the work
area.
• See statistics of your product.
Note:
All countries do not support cellular connection
®
to Automower Connect because of regional specified
cellular systems. The included Automower
lifetime service only applies if there is a third part
subsupplier of 2G/3G/4G available in the operational
area.
®
To install the Automower Connect app
1. Download the Automower
mobile device.
2. Sign up for a Husqvarna account in the
®
Automower Connect app.
3. An e-mail is sent to the registered e-mail address.
Follow the instructions in the e-mail in less than 24
hours to validate your account.
4. Log in to your Husqvarna account in the
®
Automower Connect app.
®
To pair Automower Connect and the product
To get access to the menu on
1. Do steps 1–3 in
page 22 .
2. Use the arrow buttons and the OK button to move
through the menu structure
®
Automower Connect > Pairing > New pairing .
3. Follow the instructions in the app.
To enable the GeoFence function
GeoFence is a GPS-based theft protection that makes a
virtual fence for the product. You will get a message if
the product is moved on the other side of the GeoFence.
1. Put the product in the center of the work area.
To get access to the menu on
2. Do steps 1–3 in
page 22 .
3. Use the arrow buttons and the OK button to move
through the menu structure
Automower Connect > GeoFence > Activate
GeoFence .
4. Push the OK button.
Activate GeoFence and push the OK
5. Select
button.
To set a new center point for the Geofence function
1. Put the product in the center of the work area.
To get access to the menu on
2. Do steps 1–3 in
page 22 .
3. Use the arrow buttons and the OK button to move
through the menu structure
Automower Connect > GeoFence > New center
point .
4. Push the OK button.
30 - Installation
®
Connect
®
Connect app on your
Accessories >
Accessories >
Accessories >
To set the GeoFence level of sensitivity
The higher level of GeoFence sensitivity, the easier the
alarm starts.
1. Do steps 1–3 in To get access to the menu on
page 22 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Automower Connect > GeoFence .
3. Use the arrow buttons to select level of GeoFence
sensitivity.
4. Push the BACK button.
3.10.10.3 To avoid collisions with the Automower
house
The wear on the product and the Automower
Avoid collisions with mower .
decreases when you select
To get access to the menu on
1. Do steps 1–3 in
page 22 .
2. Use the arrow buttons and the OK button to move
through the menu structure
house > Avoid collisions with mower .
Note:
Avoid collisions with mower is selected it can
If
result in grass that is not cut around the charging
station.
3.10.10.4 Headlights Automower
To set the schedule for the headlights
To get access to the menu on
1. Do steps 1–3 in
page 22 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Headlights > Schedule .
3. Select between Always ON , Evening only
Evening & night (19:00-07:00) or
(19:00-00:00),
Always OFF .
To set the Flashes when fault function
The headlights flashes if the product stops to operate
because of a fault if Flashes when fault is enabled.
To get access to the menu on
1. Do steps 1–3 in
page 22 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Headlights > Flashes when fault .
3. Use the OK button to enable or disable the
Flashes when fault function.
Accessories >
®
®
house
Accessories > Mower
® 405X/415X
Accessories >
Accessories >
1650 - 003 - 24.02.2021