Page 1
Operator's manual ® HUSQVARNA AUTOMOWER 405X/415X EN, English Read the operator's manual carefully and make sure that you understand the instructions before you use the product.
Contents 6.4 Indicator lamp in the charging station....41 1 Introduction 6.5 Symptoms............42 1.1 Introduction............3 6.6 Find breaks in the loop wire........ 43 1.2 Product overview ..........4 7 Transportation, storage and disposal 1.3 Symbols on the product........5 1.4 Symbols on the display.........
PIN code: The serial number is on the product rating plate and on the product carton. • Use the serial number to register your product on www.husqvarna.com. 1.1.1 Support The operator selects the operation settings with the keys For support about the product, speak to your Husqvarna on the keypad.
1.2 Product overview Body 17. Maintenance tool Top cover 18. Cutting system Hatch to display and keypad 19. Chassis box with electronics, battery and motors STOP button 20. Loop wire for boundary loop and guide wire Rear wheels 21. Connectors for the loop wire Front wheels 22.
1.3 Symbols on the product These symbols can be found on the product. Study them The low-voltage cable must not be carefully. shortened, extended or spliced. WARNING: Read the user in- Do not use a trimmer nearby the low- structions before operating voltage cable.
The battery indicator shows the charge level of the battery. When the product Do not discard the battery into fire and do charges the symbol flashes. not expose the battery to a heat source. The product is put in the charging station but do not charge the battery.
1.7 Menu structure overview - 1 Schedule Overview/Monday Period 1 Period 2 Copy Reset Current All week days Cutting height Cutting height TargetHeight Security Advanced Security level New loop Change Duration Medium High signal PIN code Duration of alarm Messages Fault Info messages...
1.8 Menu structure overview - 2 Installation Lawn Find charging station Advanced coverage Guide Boundary Charger GPS Auto Charging station range Disable More Delay Disable More Delay time time Area 1-3 Test Reset Test Test Reset guide right left How? Disable More Drive past...
1.9 Display The display on the product shows information and settings of the product. To access the display, push the STOP button. 1.10 Keypad Use the keypad on the product to navigate in the menu. To access the keypad, push the STOP button. •...
2 Safety 2.1 Safety information 2.1.1 IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE The operator is responsible for accidents or hazards occurring to other people or property. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities (that could affect a safe handling of the product), or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person...
The appliance must be disconnected from the supply mains when removing the battery. WARNING: The product CAUTION: Used if there is a risk of damage to the product, other materials or can be dangerous if used the adjacent area if the instructions in the manual are not obeyed.
Page 12
It is not permitted to modify the original design of code has been entered. the product. All modifications are made at your • Husqvarna does not guarantee full compatibility own risk. between the product and other types of wireless •...
Page 13
Push the ON/OFF button for 3 seconds and make sure the product is switched off. Check that the indicator lamp on the keypad is not lit. This means To use the that the product is disabled. Refer to WARNING: Use the plug to disconnect ON/OFF button on page 31 .
When the product has cut the grass for some time, the perceived sound level is much lower. Note: Refer to www.husqvarna.com for more information about installation. 3.4 Before the installation of the wires You can select to attach the wires with stakes or bury 3.2 Main components for installation...
Page 15
3.4.3 To examine where to put the • Put the charging station in an area with protection from the sun. boundary wire • If the charging station is installed on an island, make sure to connect the guide wire to the island. CAUTION: There must be a barrier of To make an island on page 17 .
Page 16
" 10 cm / 4 " max 1 cm / 0.4 • If you have a paving stone path that is in level with the lawn, put the boundary wire below the paving stone. Note: If the paving stone is minimum 30 cm / 12 Drive Past in.
Page 17
3.4.3.3 To make an island CAUTION: Do not put a section of boundary wire across the other. The >10% 0-25% sections of boundary wire must be parallel. CAUTION: Do not put the guide wire across the boundary wire. CAUTION: Isolate or remove obstacles •...
Page 18
3.4.4 To examine where to put the guide wire • Put the guide wire in a line at a minimum of 2 m / 6.5 ft. in front of the charging station. • Make as much free area as possible to the left of the guide wire when facing the charging station.
Put the power supply at a minimum height of 30 used with the power supply unit supplied by cm / 12 in. Husqvarna. WARNING: Do not put the power supply at a height where there is a risk it can be put in water.
Page 20
min 30 cm / 12” Cut the boundary wire 1-2 cm / 0.4-0.8 in. above each connector. Connect the power supply cable to a 100-240V Push the right connector onto the metal pin on the power outlet. charging station with the mark "AR". Note: When the charging station is connected, it Push the left connector onto the metal pin on the...
3.7 To bury the boundary wire or the Put the 2 ends of the boundary wire and the end of the guide wire into the coupler. guide wire Note: Make sure that you can see the ends • Cut a groove in the ground with an edge cutter or a of the wires through the transparent area of straight shovel.
3.10.3 Schedule Note: The lawn should not be cut too often to obtain the best result. If the product is allowed to operate too If the indicator LED lamp does not have a green much, the lawn may appear flattened. The product is light, do a check of the installation.
Page 23
The cutting height can be varied from MIN (2 cm / 0.8 Area, m Recommended operating in.) to MAX (5 cm / 2 in.). time, h To set the cutting height Do steps 1–3 in To get access to the menu on page 22 .
Page 24
Use the arrow buttons and the OK button to move If the product is disrupted in any way, for example it is through the menu structure Settings > Security > trapped or the battery is low, a message is saved Security level .
Page 25
the grass growth is high then the product is allowed to Area C, approximately 20% work longer. Note: If the mowing results are not optimal when Weather timer , the schedule settings may need using adjusting. Do not restrict the schedule more than necessary.
Page 26
Note: To prevent that the grass in the narrow passage Settings > Lawn through the menu structure is worn, Husqvarna recommends to set a low Coverage > Area > More > Test . Systematic Passage Mowing . percentage for the Push the OK button.
Page 27
charging station > Overview of search methods > After 3 min the product changes search method to the guide wire method. The product tries to find the guide Boundary > More > Test right / Test left . wire for 8 min. After 11 min the product changes search Push the START button and close the hatch.
Page 28
Use the arrow buttons and the OK button to move 3.10.9.1 ECO mode through the menu structure Installation > Advanced ECO mode is activated, it switches off the signal in the > Corridor width . boundary loop, the guide wire and the charging station, Use the arrow buttons to select a corridor.
Page 29
This menu handles accessories mounted on the Do steps 1–3 in page 22 . product. Contact your local Husqvarna representative for more information on available accessories. Use the arrow buttons and the OK button to move Settings > General >...
Page 30
The wear on the product and the Automower house mobile device. Avoid collisions with mower . decreases when you select Sign up for a Husqvarna account in the ® Automower Connect app. To get access to the menu on Do steps 1–3 in page 22 .
4 Operation 4.1 To use the ON/OFF button Note: If the product is parked in the charging station, the product will start to operate when the battery is fully WARNING: Read the safety Schedule settings is set for operation charged and if the instructions carefully before you start the product.
4.6 To charge the battery Note: After the product has operated in the operating Spot cutting , it will automatically start to cut in the mode WARNING: Only charge the product Main area or Secondary area . operating mode using a charging station which is intended for it.
Push the maintenance tool down in 1 of the 4 running water from a water hose. positions, and pull the body up. Husqvarna recommends to use a special cleaning and Continue with the remaining positions while you maintenance kit, available as accessory. Speak to your hold the body up.
All 3 blades and screws must be replaced at the same time to obtain a balanced cutting system. Use Husqvarna original blades embossed with the Technical data on crowned H-mark logotype, refer to page 47 .
The battery is fine as long as the product maintains a well-cut lawn. 5.5 Winter service Take your product to your Husqvarna central service for service prior to winter storage. Regular winter service will maintain the product in good condition and create the best conditions for a new season without any disruptions.
In this chapter you can find information and help about faults and symptoms of the product. You can find more information and FAQ (Frequently Asked Questions) on www.husqvarna.com. 6.2 Fault messages The fault messages in the table below are shown in the display of the product. Speak to your Husqvarna representative if the same message shows frequently. Message...
Page 37
Message Cause Action Wheel motor Grass or other object is wrapped around the Clean the wheels and around the wheels. blocked, left/right drive wheel. Wheel motor overloa- ded, left/right Wheel drive problem, right/left Cutting system Grass or other object is wrapped around the Clean the wheels and around the wheels.
Page 38
Message Cause Action Battery problem Temporary battery or firmware related issue Restart the product. If the problem stays in the product. speak to your authorized service technician. Incorrect type of battery. Use original batteries recommended by the manufacturer. Battery temperature The temperature in the battery is too high or No action.
Page 39
Message Cause Action Stuck in charging sta- There is an object in the way of the product Remove the object. tion preventing it from leaving the charging sta- tion. Charging system Incorrect type of battery. Use original batteries recommended by the problem manufacturer.
6.3 Information and warning messages The information messages in the table below are shown in the display of the product. Speak to your Husqvarna representative if the same message shows frequently. Message Cause Action Limited cutting height The cutting height adjustment cannot move.
The indicator lamp in the charging station must show a solid or flashing green light for a correct installation. If not, follow the instructions in the troubleshooting guide below. Speak to your Husqvarna customer service for more information. Light Cause...
6.5 Symptoms If the product does not operate as usual, follow the symptoms table below. Speak to your Husqvarna customer service if you cannot find the cause for the fault. Symptoms Cause Action The product has diffi- The guide wire is not put straight in a line...
Symptoms Cause Action Schedule on page 22 . The product is The product has operated the maximum cut- No action. Refer to parked for hours in ting time for the day. the charging station. The hatch is closed but the START button is Push the STOP button to open the hatch.
Page 44
Start by switching connection AL and GUIDE. If the indicator lamp has a solid green light, then the break is somewhere on the boundary wire between AL and the point where the guide wire is connected to the boundary wire (thick black line in the illustration).
Page 45
Continue until only a very short section of the wire remains which is the difference between a solid green light and a flashing blue light. Then follow instruction in step 5 below. If indicator lamp still flashes blue in step 3 above: Put AL and GUIDE back in their original positions.
7.3.1 To remove the battery CAUTION: Only remove the battery when you dispose the product. When you remove the warranty seal, the Husqvarna warranty is no longer applicable. Remove the top cover and the body of the product. To clean the chassis and blade Follow steps 1-7 in disc on page 33 .
8 Technical data ® 8.1 Automower 405X/415X ® ® Dimensions Automower 405X Automower 415X Length, cm / in 61 / 24.0 61 / 24.0 Width, cm / in 45 / 17.7 45 / 17.7 Height, cm / in 24 / 9.4 24 / 9.4 Weight, kg / lbs 9.7 / 21.4...
Page 48
Connect 4G Power Class 3 23 dBm Husqvarna AB does not guarantee full compatibility between the product and other types of wireless systems such as remote controls, radio transmitters, hearing loops, underground electric animal fencing or similar. 48 - Technical data...
3 8.2 Registered trademarks Bluetooth ® Bluetooth SIG, inc. and any use of such word mark and logos are registered trademarks owned by marks by Husqvarna is under license. 1650 - 003 - 24.02.2021 Technical data - 49...
The blades and wheels are seen as disposable and are not covered by the warranty. If an error occurs with your Husqvarna product, please contact Husqvarna customer service for further instructions. Please have the receipt and the product’s serial number at hand when contacting Husqvarna customer service.