Husqvarna Automower 405X Operator's Manual page 27

After 3 min the product changes search method to the
guide wire method. The product tries to find the guide
wire for 8 min. After 11 min the product changes search
method to the boundary wire method.
You can change the settings for how the product finds
the charging station to adapt to the work area.
To set how the product finds the charging station
You can make manual settings to make the product
search for the guide wire or the boundary wire in 0–30
min from when the battery is low.
1. Do steps 1–3 in To get access to the menu on
page 22 .
2. Use the arrow buttons and the OK button to move
through the menu structure
the charging station > Overview of search methods
> Guide .
3. Push the arrow buttons to select 1 of the guide
wires.
4. Push the number buttons to set the time.
5. Push the OK button.
6. Push the BACK button.
7. Use the arrow buttons and the OK button to move
through the menu structure
the charging station > Overview of search methods
> Boundary wire .
8. Push the number buttons to set the time.
9. Push the OK button.
10. Push the START button and close the hatch.
To do a test of the guide wire
To get access to the menu on
1. Do steps 1–3 in
page 22 .
2. Use the arrow buttons and the OK button to move
through the menu structure
charging station > Guide > More > Test guide .
3. Put the product 3 m / 9 ft. from the boundary wire.
4. Push the START button and close the hatch.
5. Make sure the product follows the guide wire to the
charging station.
6. Make sure the product docks with the charging
station.
7. If the product does not dock with the charging
station, change the position of the charging station
or the guide wire. Refer to
station on page 19 and To install the guide wire on
page 20 .
To do a test of the boundary wire
1. Put the product 3 m / 9 ft. from the boundary wire,
facing the boundary wire.
To get access to the menu on
2. Do steps 1–3 in
page 22 .
3. Use the arrow buttons and the OK button to move
through the menu structure
1650 - 003 - 24.02.2021
Installation > To find
Installation > To find
Installation > Find
To install the charging
Installation > Find
charging station > Overview of search methods >
Boundary > More > Test right / Test left .
4. Push the START button and close the hatch.
5. Make sure the product follows the guide wire to the
charging station.
6. Make sure the product docks with the charging
station.
7. Change the position of the charging station or the
guide wire if the product does not dock with the
charging station. Refer to
station on page 19 and To install the guide wire on
page 20 .
To change the signal range of the charging station
To get access to the menu on
1. Do steps 1–3 in
page 22 .
2. Use the arrow buttons and the OK button to move
through the menu structure
charging station > Overview of search methods >
Charging station range .
3. Use the left arrow button to select
4. Push the BACK button.
Note:
It is usually better to move the charging station,
than to decrease the range of the charging station
signal.
3.10.8.3 Corridor width
The area adjacent to the boundary wire is the corridor
that the product uses to move to the charging station.
The corridor width is a measure of how far from the
boundary wire the product can operate when following
the boundary wire to and from the charging station.
The corridor width is adjusted automatically. If it is
necessary to adjust the corridor width manually for the
product to operate satisfactorily, you can set the corridor
width between 1-9. The factory setting is 6.
To set the corridor width
To get access to the menu on
1. Do steps 1–3 in
page 22 .
To install the charging
Installation > Find the
MAX, MID, MIN .
Installation - 27